MODEL: SC200

SC200 SPECIFICATIONS

ES-6338 Rev.17 Page 2/12

http://www.m-system.co.jp/

saving and transfer with PC Configurator Software (model:

SCCFG)

• Control and supervision by SCADA software via Modbus

TCP/IP or RTU communication

• Selectable housing depth for ease of using existing wires

in replacement: 250 mm, 300 mm and 400 mm

• Separable terminal block

Typical Applications

• Replacement of conventional controllers

• Panel operation for small-scale instrumentation

RELATED PRODUCTS

• PC Configurator cable (model: COP-US)

• Loop configuration builder software (model: SFEW3E Ver.

1.40 or later)

• Infrared communication adaptor (model: COP-IRDA)

• PC configurator software (model: SCCFG Ver.1.50 or later)

Builder software and configurator software are

downloadable at M-System’s web site.

ACCESSORIES

• Precision resistor module (model: REM4): 2

• Cold junction sensor: 2

• Mounting brackets: 2

• Connector adapter: 1

(included in Stereo jack type. The jack on the unit and the

plug of PC Configurator cable (not included in the product)

are different in size.)

GENERAL SPECIFICATIONS

Construction: Panel flush mounting

Degree of protection: IP55; ensured for the front panel of

the unit independently mounted to a panel

Connection

Terminal screws: M3.5 screw terminals (torque 1.0 N·m)

Terminal fixing screws: M4 screw terminals

(torque 1.2 N·m)

Ethernet: RJ-45 Modular Jack

Screw terminal

Terminal screws: Nickel-plated steel (standard) or stainless

steel

Terminal fixing screws: Chrome-plated steel

Housing material: Flame-resistant resin (gray), steel

Isolation: Pv1 to Pv2 to supply output to Ai1 or Ai2 or Ai3 or

Ai4 to Di1 or Di2 or Di3 or Di4 or Di5 or Pi1 or Pi2 or Pi3 or

Pi4 or Pi5 to Di6 or Pi6 to Mv1 to Mv2 to Ao1 or Ao2 to Do1

to Do2 to Do3 to Do4 to Do5 to Do6 to NestBus to Modbus-

RTU to Modbus/TCP to power to FG

PID control: Single loop, cascade, advanced

Proportional band (P): 1 to 1000 %

Integral time (I): 0.01 to 100 minutes

Derivative time (D): 0.01 to 10 minutes

Auto-tuning: Limit cycle method

Alarm: PV high & low, deviation, rate of change

Computation: 48 functions blocks available for arithmetic

operations, time functions, signal selection, limit, alarm and

other functions

Sequence operation: Logic sequence and step sequence

(max. 1068 commands)

Computation cycle: 50 msec. to 3 sec. (control cycle

selectable among 1, 2, 4, 8, 16, 32 and 64 times of the

computation cycle)

MV output range: -15 - +115 %

Parameter setting: With touch panel or PC (Loop

Configuration Builder Software model: SFEW3E)

Self diagnostics: CPU monitoring with a watchdog timer

RUN contact: OFF in error detected by diagnostic (including

NestBus)

Infrared communication: Transmission distance max. 0.2

meter (for use with the COP-IRDA)

Short trend

Storing interval: 1, 2, 5, 10, 20, 30 sec.,

1, 2, 5, 10, 30, 60 min.

Capacity: 400 points (display 200 points)

■ Display

Display device: 4.3-inch TFT LCD

Display colors: 256

Resolution: 480 × 272 pixels

Pixel pitch: 0.198 × 0.198 mm (128 × 128 DPI)

Backlight: LED

Backlight life: Approx. 50 000 hours (at 50 % brightness)

Note: The backlight can be replaced in M-System factory.

The LCD must be replaced at the same time.

Screen saver standby time: 1 to 99 minutes

Scaling range: -32000 to +32000

Scale divisions: 2 to 10

Engineering unit indication: Max. 8 characters

Auto/Man indicator: Green/Amber LED