MODEL: YPD

YPD SPECIFICATIONS

ES-1369 Rev.13 Page 2/6

http://www.m-system.co.jp/

GENERAL SPECIFICATIONS

Construction: Plug-in

Connection: M3.5 screw terminals

Screw terminal: Chromated steel (standard) or stainless

steel

Housing material: Flame-resistant resin (black)

Isolation: Input to output to power

Excitation adjustment: 5 – 12 V DC

Detecting level adjustments (DC voltage pulse): 2 – 10 V

Input pulse sensing: DC coupled

Input filter: Provided with output code A2, M2, N2, H

(time constant approx. 1 msec.)

INPUT SPECIFICATIONS

Excitation: Shortcircuit protection; approx. 150 mA at

shortcircuit

■ Dry Contact

Max. frequency: 100 kHz

Pulse width time requirement: 5 μsec. min. (10 ms

for output code A2, M2, N2, H)

Sensing: 10 V DC @ 2.5 mA

ON/OFF level:

≥ 5.5 kΩ /5.5 V for OFF

≤ 1.8 kΩ /4.5 V for ON

■ Voltage Pulse: Specify DC offset and amplitude.

Max. frequency: 100 kHz

Pulse width time requirement: 5 μsec. min. (10 ms

for output code A2, M2, N2, H)

Waveform: Square or sine

Input impedance: 10 kΩ min.

Input amplitude: 2 – 50 Vp-p

Sensitivity adjustment (threshold level): 2 – 10 V

Max. voltage between input terminals: 50 V

• 5V, 12V, 24V Pulse

Waveform: Square or sine

Input impedance: 10 kΩ min.

Detecting level

INPUT

5 V PULSE

12 V / 24 V PULSE

≥ 2.25 V

≥ 5.25 V

≤ 1.75 V

≤ 4.75 V

■ Two-wire Current Pulse

Max. frequency: 100 kHz

Pulse width time requirement: 5 μsec. min. (10 ms

for output code A2, M2, N2, H)

Input resistance: Receiving resistor 220 Ω

Maximum current: ± 50 mA

Hi/Lo level: ≤ 5 mA for Lo, ≥ 15 mA for Hi

50V max.

Amplitude

Vinp-p

t

Volts

DC Offset

■ Voltage pulse waveform

OUTPUT SPECIFICATIONS

■ Open Collector: 50 V DC @ 50 mA (resistive load)

Maximum frequency:

Output code A1: 100 kHz with load resistance ≤ 1 kΩ

OUtput code A2: 10 Hz with load resistance ≤ 1 kΩ

Saturation voltage: 0.5 V DC

■ Voltage Pulse: Rating (5 or 12 V) ± 10 %

Maximum frequency: 100 kHz

Load resistance: 1.5 kΩ min. for 5 V, 3 kΩ min. for 12 V

L level: ≤ 0.5 V

■ Relay Contact: 120 V AC or 30 V DC @ 200 mA

(resistive load)

Maximum switching voltage: 250 V AC or 30 V DC

Maximum switching power: 50 VA or 6 W

Minimum load: 5 V DC @ 10 mA

Maximum frequency: 0.5 Hz

Relay life:

OUTPUT PULSE WIDTH

•Equal to the Input: No pulse width conversion

(difference between input and output within ±10 μsec.)

• One-shot Output: Constant pulse width

Output Frequency (Hz) = 500 / (Output Pulse Width (msec.))

Adjustable pulse width

Pulse width max. 30 msec. (code 2):

1 – 30 msec. adjustable (standard 5 msec. ±20 %) for

'Output' code other than 'H'

10 – 30 msec. adjustable (standard 10 msec. ±20 %) for

'Output' code 'H'

Pulse width min. 30 msec. (code 3): 30 msec. – 1 sec.

adjustable (standard 50 msec. ±20 %)