USB7216CSLASHKDX datasheet(23/60 Pages) MICROCHIP

23 / 60 page



2021 Microchip Technology Inc.

DS00003851A-page 23

USB7216C

PRT_CTL2

I/O12

(PU)

Port 2 power enable / overcurrent sense

When the downstream port is enabled, this pin is set as an input

with an internal pull-up resistor applied. The internal pull-up

enables power to the downstream port while the pin monitors for an

active low overcurrent signal assertion from an external current

monitor on USB port 2.

This pin will change to an output and be driven low when the port is

disabled by configuration or by the host control.

Note:

When PortSplit is disabled, this signal controls both the

USB 2.0 and USB 3.2 portions of the port. When

PortSplit is enabled, this signal controls the USB 2.0

portion of the port only.

Note 3-8

This pin can be left unused only if Port 2 is

disabled via strap/OTP/SMBus/SPI configuration.

Float

(Note 3-4)

PRT_CTL1

I/O12

(PU)

Port 1 power enable / overcurrent sense

When the downstream port is enabled, this pin is set as an input

with an internal pull-up resistor applied. The internal pull-up

enables power to the downstream port while the pin monitors for an

active low overcurrent signal assertion from an external current

monitor on USB port 1.

This pin will change to an output and be driven low when the port is

disabled by configuration or by the host control.

Note:

This signal controls both the USB 2.0 and USB 3.2 por-

tions of the port.

Note 3-9

This pin can be left unused only if Port 1 is

disabled via strap/OTP/SMBus/SPI configuration.

Float

(Note 3-4)

PRT_CTL4_U3

O12

Port 4 USB 3.2 PortSplit power enable

This signal is an active high control signal used to enable to the

USB 3.2 portion of the downstream port 4 when PortSplit is

enabled. When PortSplit is disabled, this pin is not used.

Note:

This signal should only be used to control an embedded

USB 3.2 device.

Float

PRT_CTL3_U3

O12

Port 3 USB 3.2 PortSplit power enable

This signal is an active high control signal used to enable to the

USB 3.2 portion of the downstream port 3 when PortSplit is

enabled. When PortSplit is disabled, this pin is not used.

Note:

This signal should only be used to control an embedded

USB 3.2 device.

Float

TABLE 3-6:

PROGRAMMABLE FUNCTIONS DESCRIPTIONS (CONTINUED)

Function

Buffer

Type

Description

If Unused

USB7216C/KDX 数据表(PDF) 23 Page - Microchip Technology

USB7216C/KDX 数据表(HTML) 23 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

数据表下载

链接网址

USB7216C/KDX 数据表(PDF) 23 Page - Microchip Technology

USB7216C/KDX 数据表(HTML) 23 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

数据表 下载

链接网址

数据表下载