USB7016SLASHKDX datasheet(39/60 Pages) MICROCHIP

39 / 60 page

 2022 Microchip Technology Inc. and its subsidiaries

DS00003740B-page 39

USB7016

8.6

USB to GPIO Bridging

The USB to GPIO bridging feature provides system designers expanded system control and potential BOM reduction.

General Purpose Input/Outputs (GPIOs) may be used for any general 3.3V level digital control and input functions.

Commands may be sent from the USB Host to the internal Hub Feature Controller device in the Microchip hub to per-

form the following functions:

• Set the direction of the GPIO (input or output)

• Enable a pull-up resistor

• Enable a pull-down resistor

• Read the state

• Set the state

For detailed information on utilizing the USB to GPIO bridging feature, refer to the application note “AN2750 USB to

GPIO Bridging with Microchip USB70xx Hubs

”, which can be found on the Microchip USB7016 product page at

www.microchip.com/USB7016.

8.7

USB to I2C Bridging

The USB to I2C bridging feature provides system designers expanded system control and potential BOM reduction. The

use of a separate USB to I2C device is no longer required and a downstream USB port is not lost, as occurs when a

standalone USB to I2C device is implemented.

Commands may be sent from the USB Host to the internal Hub Feature Controller device in the Microchip hub to per-

form the following functions:

•Configure I2C Pass-Through Interface

•I2C Write

•I2C Read

For detailed information on utilizing the USB to I2C bridging feature, refer to the application note “AN2754 USB to I2C

Bridging with Microchip USB70xx Hubs

”, which can be found on the Microchip USB7016 product page at www.micro-

chip.com/USB7016.

8.8

USB to SPI Bridging

The USB to SPI bridging feature provides system designers expanded system control and potential BOM reduction. The

use of a separate USB to SPI device is no longer required and a downstream USB port is not lost, as occurs when a

standalone USB to SPI device is implemented.

Commands may be sent from the USB Host to the internal Hub Feature Controller device in the Microchip hub to per-

form the following functions:

• Enable SPI Pass-Through Interface

• SPI Write/Read

• Disable SPI Pass-Through Interface

For detailed information on utilizing the USB to SPI bridging feature, refer to the application note “AN2790 USB to SPI

Bridging with Microchip USB70xx Hubs

”, which can be found on the Microchip USB7016 product page at www.micro-

chip.com/USB7016.

USB7016/KDX 数据表(PDF) 39 Page - Microchip Technology

USB7016/KDX 数据表(HTML) 39 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

数据表下载

链接网址

USB7016/KDX 数据表(PDF) 39 Page - Microchip Technology

USB7016/KDX 数据表(HTML) 39 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60

数据表 下载

链接网址

数据表下载