STATIC

Supply Voltage Range

Quiescent Current

INPUT

Input Offset Voltage

Input Offset Voltage Drift

Input Offset Adjust

Input Bias Current

Input Offset Current

Input Impedance

Power Supply Rejection Ratio

Common Mode Rejection Ratio

Input Noise Voltage

Equivalent Input Noise

OUTPUT

Output Voltage Swing

Output Current

Settling Time to 1%

Settling Time to 0.1%

Full Power Bandwidth

Bandwidth (Small Signal)

TRANSFER CHARACTERISTICS

Slew Rate Limit

Open Loop Voltage Gain

Either Input

F=DC

F=10Hz To 1KHz

F=1KHz

±18V

±40mA

±30V

-55°C to +125°C

-40°C to +85°C

187°C/W

ABSOLUTE MAXIMUM RATINGS

Storage Temperature Range

Lead Temperature Range

(10 Seconds)

Junction Temperature

-65°C to +150°C

300°C

175°C

Supply Voltage

Output Current

Differential Input Voltage

Case Operating Temperature Range

(MSK 032B/E)

(MSK 032)

Thermal Resistance

(Output Switches) (Junction to Case)

ELECTRICAL SPECIFICATIONS

±Vcc=±15VDC Unless Otherwise Specified

Min.

±10

-

-

-

-

-

-

-

-

-

60

70

-

-

±10

±20

-

-

8

80

500

80

Max.

±18

±20

±25

±5

±25

±250

±10

100

5

-

-

-

-

-

-

-

60

90

-

-

-

-

Min.

±10

-

-

-

-

-

-

-

-

-

-

55

65

-

-

±10

±20

-

-

7

75

475

75

Max.

±18

±22

-

±7

-

-

±300

-

150

-

-

-

-

-

-

-

-

65

100

-

-

-

-

Units

V

mA

mA

mV

µV/°C

mV

mV

pA

nA

pA

nA

Ω

dB

dB

µVrms

nV√Hz

V

mA

nS

nS

MHz

MHz

V/µS

dB

MSK 032B/E

MSK 032

2

Typ.

±15

±15

-

±1

-

-

±75

-

20

-

10

70

80

1.5

40

±12

±30

55

70

8

80

550

85

Test Conditions

Parameter

7

Typ.

±15

±15

±18

±0.5

±10

±50

±0.2

10

0.1

10

70

80

1.5

40

±12

±30

50

60

9

90

600

90

Adjust to Zero

Adjust to Zero

12

12

Group A

Subgroup

-

1

2,3

1

2,3

1

2,3

1

2,3

1

2,3

-

-

-

-

-

4

4

4

4

4

4

4

4

Adjust to Zero

1

2

2

2

2

2

2

2

1

2

3

4

5

6

7

AV=-1, measured in false summing junction circuit.

Devices shall be capable of meeting the parameter, but need not be tested. Typical parameters are for reference only.

Industrial grade and "E" suffix devices shall be tested to subgroups 1 and 4 unless otherwise specified.

Military grade devices ('B' suffix) shall be 100% tested to subgroups 1,2,3 and 4.

Subgroup 5 and 6 testing available upon request.

Subgroup 1,4

Subgroup 2,5

Subgroup 3,6

Electrical specifications are derated for power supply voltages other than ±15VDC.

NOTES:

Rev. B 5/02

2