Rev 2.1 ©2010 Advanced Linear Devices, Inc. 415 Tasman Drive, Sunnyvale, CA 94089-1706 Tel: (408) 747-1155 Fax: (408) 747-1286

www.aldinc.com

GENERAL DESCRIPTION

The ALD1701A/ALD1701B/ALD1701/ALD1701G is a monolithic CMOS

micropower high slew rate operational amplifier intended for a broad

range of analog applications using ±1V to ±5V dual power supply

systems, as well as +2V to +10V battery operated systems. All device

characteristics are specified for +5V single supply or ±2.5V dual supply

systems. Supply current is 250µA maximum at 5V supply voltage. It is

manufactured with Advanced Linear Devices' enhanced ACMOS silicon

gate CMOS process.

The ALD1701A/ALD1701B/ALD1701/ALD1701G is designed to offer a

trade-off of performance parameters providing a wide range of desired

specifications. It has been developed specifically for the +5V single

supply or ±1V to ±5V dual supply user and offers the popular industry

standard pin configuration of µA741 and ICL7611 types.

Several important characteristics of the device make application easier to

implement at those voltages. First, the operational amplifier can operate

with rail to rail input and output voltages. This means the signal input

voltage and output voltage can be equal to the positive and negative

supply voltages. This feature allows numerous analog serial stages and

flexibility in input signal bias levels. Second, the device was designed to

accommodate mixed applications where digital and analog circuits may

operate off the same power supply or battery. Third, the output stage can

typically drive up to 50pF capacitive and 10KΩ resistive loads.

These features, combined with extremely low input currents, high open

loop voltage gain of 100V/mV, useful bandwidth of 700KHz, a slew rate

of 0.7V/µs, low power dissipation of 0.5mW, low offset voltage and

temperature drift, make the ALD1701 a versatile, micropower operational

amplifier.

The ALD1701A/ALD1701B/ALD1701/ALD1701G, designed and fabri-

cated with silicon gate CMOS technology, offers 1pA typical input bias

current. On chip offset voltage trimming allows the device to be used

without nulling in most applications. Additionally, robust design and

rigorous screening make this device especially suitable for operation in

temperature-extreme environments and rugged conditions.

FEATURES

• All parameters specified for +5V single

supply or ±2.5V dual supply systems

• Rail to rail input and output voltage ranges

• No frequency compensation required --

unity gain stable

• Extremely low input bias currents --

1.0pA typical (30pA max.)

• Ideal for high source impedance applications

• Dual power supply ±1.0V to ±5.0V operation

• Single power supply +2.0V to +10.0V

operation

• High voltage gain -- typically 100V/mV

@ ±2.5V(100dB)

• Drive as low as 10KΩ load

• Output short circuit protected

• Unity gain bandwidth of 0.7MHz

• Slew rate of 0.7V/µs

• Low power dissipation

• Suitable for rugged, temperature-extreme

environments

MICROPOWER RAIL-TO-RAIL CMOS OPERATIONAL AMPLIFIER

ALD1701A/ALD1701B

ALD1701/ALD1701G

APPLICATIONS

• Voltage amplifier

• Voltage follower/buffer

• Charge integrator

• Photodiode amplifier

• Data acquisition systems

• High performance portable instruments

• Signal conditioning circuits

• Sensor and transducer amplifiers

• Low leakage amplifiers

• Active filters

• Sample/Hold amplifier

• Picoammeter

• Current to voltage converter

PIN CONFIGURATION

* N/C pins are internally connected. Do not connect externally.

1

2

2

3

4

8

7

6

5

N/C

-IN

+IN

N/C

OUT

N/C

V-

V+

Operating Temperature Range

0°C to +70°C0°C to +70°C

-55°C to 125°C

8-Pin

8-Pin

8-Pin

Small Outline

Plastic Dip

CERDIP

Package (SOIC)

Package

Package

ALD1701ASAL

ALD1701APAL

ALD1701ADA

ALD1701BSAL

ALD1701BPAL

ALD1701BDA

ALD1701SAL

ALD1701PAL

ALD1701DA

ALD1701GSAL

ALD1701GPAL

ALD1701GDA

* Contact factory for leaded (non-RoHS) or high temperature versions.

ORDERING INFORMATION (“L” suffix denotes lead-free (RoHS))

TOP VIEW

SAL, PAL, DA PACKAGES