ADP5589ACBZ-01-R7 datasheet(23/52 Pages) AD

23 / 52 page

Data Sheet

ADP5589

Rev. B | Page 23 of 52

DETAILED REGISTER DESCRIPTIONS

Note: N/A throughout this section means not applicable.

Note: All registers default to 0000 0000 unless otherwise specified.

ID Register 0x00

Table 7. ID Bit Descriptions

Bits

Name

R/W

Description

[7: 4]

MAN_ID

Manufacturer ID, default = 0001.

[3:0]

REV_ID

Rev ID.

Default = 0001 XXXX

INT_STATUS Register 0x01

Table 8. INT_STATUS Bit Descriptions

Bits

Name

R/W

Description

[7: 6]

N/A

Reserved.

LOGIC2_INT

R/W

0 = no interrupt.

1 = interrupt due to a general Logic 2 condition.

Write a 1 to this bit to clear it.

LOGIC1_INT

R/W

0 = no interrupt.

1 = interrupt due to a general Logic 1 condition.

Write a 1 to this bit to clear it.

LOCK_INT

R/W

0 = no interrupt.

1 = interrupt due to a lock/unlock condition.

The user can read LOCK_STAT (0x02[5]) to determine if LOCK_INT is due to a lock or unlock event.

If LOCK_STAT = 1, LOCK_INT is due to a lock event.

If LOCK_STAT = 0, LOCK_INT is due to an unlock event.

Write a 1 to this bit to clear it.

If lock mode is enabled via the software bit LOCK_EN (0x37[0]), a LOCK_INT is not generated

because the processor knows it just enabled lock mode.

If lock mode is disabled (while locked) via the software bit LOCK_EN, a LOCK_INT is not generated

because the processor knows it just disabled lock mode.

OVRFLOW_INT

R/W

0 = no interrupt.

1 = interrupt due to an overflow condition.

Write a 1 to this bit to clear it.

GPI_INT

R/W

0 = no interrupt.

1 = interrupt due to a general GPI condition.

This bit is not set by a GPI that has been configured to update the FIFO and event count.

Write a 1 to this bit to clear it.

This bit cannot be cleared until all GPI_x_INT bits are cleared.

EVENT_INT

R/W

0 = no interrupt.

1 = interrupt due to key event (press/release), GPI event (GPI programmed for FIFO updates), or

Logic 1/Logic 2 event (programmed for FIFO updates).Write a 1 to this bit to clear it.

Status Register 0x02

Table 9. Status Bit Descriptions

Bits

Name

R/W

Description

LOGIC2_STAT

0 = output from Logic Block 2. (LY2) is low.

1 = output from Logic Block 2. (LY2) is high.

LOGIC1_STAT

0 = output from Logic Block 1 (LY1) is low.

1 = output from Logic Block 1 (LY1) is high.

LOCK_STAT

0 = unlocked.

1 = locked.

[4:0]

EC[4:0]

Event count value. Indicates how many events are currently stored on the FIFO.

ADP5589ACBZ-01-R7 数据表(PDF) 23 Page - Analog Devices

ADP5589ACBZ-01-R7 数据表(HTML) 23 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

数据表下载

链接网址

ADP5589ACBZ-01-R7 数据表(PDF) 23 Page - Analog Devices

ADP5589ACBZ-01-R7 数据表(HTML) 23 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

数据表 下载

链接网址

数据表下载