SFSKA6M50CF00-R3 datasheet(66/77 Pages) MURATA1

66 / 77 page

Notice

o Storage and Operating Conditions

o Rating

The component may be damaged if excessive mechanical

stress is applied.

o Soldering and Mounting

The component cannot withstand washing.

o Handling

1. Do not use this product with bend. The component may

be damaged if excessive mechanical stress is applied to

it mounted on the printed circuit board.

2. All kinds of reflow soldering must not be applied on the

component.

3. Do not clean or wash the component as it is not

hermetically sealed.

4. Do not use strong acidity flux, more than 0.2wt% chlorine

content, in flow soldering.

5. Conformal coating of the component is not acceptable

due to non-sealed construction.

6. Accurate test circuit values are required to measure

electrical characteristics. Miscorrelation may be caused if

there is any deviation, especially stray capacitance, from

the test circuit in the specification.

7. For safety purposes, connect the output of filters to the IF

amplifier through a D.C. blocking capacitor. Avoid

applying a direct current to the output of ceramic filters.

1. Product Storage Conditions

Please store the products in a room where the

temperature/humidity is stable, and avoid places where

there are large temperature changes. Please store the

products under the following conditions:

Temperature: -10 to +40°C

Humidity: 15 to 85% R.H.

2. Expiration Date on Storage

Expiration date (shelf life) of the products is six months

after delivery under the conditions of a sealed and

unopened package. Please use the products within six

months after delivery. If you store the products for a long

time (more than six months), use carefully because

solderability may be degraded due to storage under poor

conditions.

Please confirm solderability and characteristics for the

products regularly.

3. Notice on Product Storage

(1) Please do not store the products in a chemical

atmosphere (Acids, Alkali, Bases, Organic gas,

Sulfides and so on), because quality and solderability

may be degraded due to storage in a chemical

atmosphere.

(2) Please do not put the products directly on the floor

without anything under them to avoid damp places

and/or dusty places.

(3) Please do not store the products in places such as a

damp heated place or any place exposed to direct

sunlight or excessive vibration.

(4) Please use the products immediately after package is

opened, because quality and solderability may be

degraded due to storage under poor conditions.

(5) To avoid cracking of ceramic element, please do not

drop the products.

4. Other

Please be sure to consult with our sales representative or

engineer whenever the products are to be used in

conditions not listed above.

c CERAFILr 455kHz Lead Type SFPLA/CFWLA/CFULA Series

!Note • Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.

• This catalog has only typical speciﬁcations. Therefore, please approve our product speciﬁcations or transact the approval sheet for product speciﬁcations before ordering.

SFSKA6M50CF00-R3 数据表(PDF) 66 Page - Murata Manufacturing Co., Ltd

SFSKA6M50CF00-R3 数据表(HTML) 66 Page - Murata Manufacturing Co., Ltd

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77

数据表下载