B7AH-R6D58 datasheet(54/121 Pages) OMRON

54 / 121 page

B7AM-6BS

Specifications

Characteristics

General

Normal speed

High speed

Communications method

Unidirectional, time-division multiplex

Transmission distance

500 m max.

100 m max. (see note 1)

I/O delay time

Typical: 19.2 ms; 31 ms max.

Typical: 3 ms; 5 ms max.

Minimum input time (see note 2)

16 ms

2.4 ms

Operating voltage range

12 to 24 VDC (10.8 to 26.4 VDC)

Insulation resistance

100 M

Ω min. (500 V) between each terminal and external parts

Dielectric strength

1,000 VAC, 50/60 Hz for 1 min between each terminal and external parts

Noise immunity (see note 3)

Noise level: 1.5 kV; pulse width: 100 ns to 1

µs

Vibration resistance

10 to 55 Hz, 1.5-mm double amplitude

Shock resistance

300 m/s2

Ambient temperature

Operating: –10 to 55

°C (with no icing)

Storage:

–25 to 65

°C (with no icing)

Ambient humidity

Operating: 35% to 85% (with no condensation)

Note:

1. A shielded transmission cable or a VCTF cable with a thickness of 0.75 mm2 minimum must be used for signal transmission. If the

VCTF cable is used, however, the transmission distance will be 10 m maximum regardless of whether or not independent power

supplies for the Input and the Output Link Terminals are used.

2. The minimum input time is required for the B7AM to read an input signal.

3. As for the high-speed model, these values are possible without grounding the shielded line.

Screw Terminal Model

Item

B7AM-6BS

I/O delay time

Normal speed (typical 19.2 ms); high speed (typical 3 ms) (switch selectable) (see note 4)

Current consumption (see note 1)

240 mA max. with all input/output terminals ON

Operating voltage range

12 to 24 VDC

Compatible inputs (see note 2)

Switches, two-wire sensors with DC output, three-wire NPN sensors

Input logic

Active low

Input voltage range

0 VDC to supply voltage

Input current range

–6 to –3 mA/point (current flowing from input terminals)

Minimum input time

Normal speed: 16 ms; high speed: 2.4 ms

ON/OFF threshold

No-contact input: ON voltage:

4 V max.

OFF voltage: 6 V min.

Contact input:

ON discrimination resistance:

660

Ω max.

OFF discrimination resistance:

2 k

Ω min.

Output configuration

NPN open collector

Rated load voltage

5 to 24 VDC

Output residual voltage

0.8 V max.

Output current

Sync. current, 100 mA max./ point

Error processing

HOLD/LOAD OFF is set using a selection switch (see note 3)

Mounting strength

No damage when 49-N pull is applied for 1 min each in all directions

Terminal strength

No damage when 49-N pull is applied for 1 min each in all directions

Tightening torque

0.78 to 1.18 N

S m

Weight

Approx. 230 g

Note:

1. Consumption when all 16 input/output points are ON. Excludes external sensor current for Input Terminals and external load current

and error load current for Output Terminals.

2. Power must be supplied to the three-wire sensor via the positive power supply terminal or from an independent power supply.

Two-wire sensors must satisfy the following requirements:

Residual voltage:

4 V max.

Current leakage:

1.5 mA max.

The lower limit of control output:

3 mA (Use a bleeder resister to eliminate this restriction.)

3. Default settings are 19.2 ms and LOAD OFF.

B7AH-R6D58 数据表(PDF) 54 Page - Omron Electronics LLC

B7AH-R6D58 数据表(HTML) 54 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载