S8FS-G10024CD-R datasheet(29/34 Pages) OMRON

29 / 34 page

S8FS-G

Safety Precautions

Refer to Safety Precautions for All Power Supplies.

Warning Indications

Meaning of Product Safety Symbols

!CAUTION

Minor electric shock, fire, or Product failure may

occasionally occur. Do not disassemble, modify, or

repair the Product or touch the interior of the

Product.

Minor burns may occasionally occur. Do not touch

the Product while power is being supplied or

immediately after power is turned OFF.

Fire may occasionally occur. Tighten terminal screws

to the specified torque.

M3.5: 0.74 to 1.13N·m

M4:

1.08 to 1.32N·m

Minor injury due to electric shock may occasionally

occur. Do not touch the terminals while power is

being supplied.

Minor electric shock, fire, or Product failure may

occasionally occur. Do not allow any pieces of metal

or conductors or any clippings or cuttings resulting

from installation work to enter the Product.

Ambient Operating and Storage Environments

• Store the Power Supply at a temperature of

−25 to 75°C and a

humidity of 90% max.

• The internal parts may occasionally deteriorate or be damaged.

Use the Power Supply within the derating curve.

• Use the Power Supply at a humidity of 90% max.

• Do not use locations where liquids, foreign matter, or corrosive

gases may enter the interior of the Power supplies.

Installation Environment

• Do not use the Power Supply in locations subject to shocks or

vibrations. In particular, install the Power Supply as far away as

possible from contractors or other devices that are a vibration

source.

• Install the Power Supply well away from any sources of strong,

high-frequency noise and surge.

Mounting

• Take adequate measures to ensure proper heat dissipation to

increase the long-term reliability of the Power Supply.

Be sure to allow convection in the atmosphere around devices

when mounting.

Do not use in locations where the ambient temperature exceeds

the range of the derating curve.

The S8FS-G015

@@@ to S8FS-G150@@@ are cooled by natural

convection. Mount them so that air convection will occur around

them.

The S8FS-G300

@@@ and S8FS-G600@@@ are cooled by forced

airflow. Do not allow the ventilation holes to be blocked. The

effectiveness of cooling would be reduced.

• When cutting out holes for mounting, make sure that cuttings do

not enter the interior of the Power supplies.

• The internal parts may occasionally deteriorate and be broken due

to adverse heat radiation. Do not loosen the screws on the Power

Supply.

• If you mount the Power Supply with the holes provided on the

chassis, do not exceed the depth given in the dimensional

diagrams.

Use the following tightening torques.

M3 screws: 0.48 to 0.59 N·m

M4 screws: 1.08 to 1.32 N·m

CAUTION

Indicates a potentially hazardous

situation which, if not avoided, may

result in minor or moderate injury or in

property damage.

Precautions for

Safe Use

Supplementary comments on what to

do or avoid doing, to use the product

safely.

Precautions for

Correct Use

Supplementary comments on what to

do or avoid doing, to prevent failure to

operate, malfunction or undesirable

effect on product performance.

Used to warn of the risk of electric shock under

specific conditions.

Used to warn of the risk of minor injury caused by

high temperatures.

Use to indicate prohibition when there is a risk of

minor injury from electrical shock or other source

if the product is disassembled.

Used for general mandatory action precautions

for which there is no specified symbol.

Precautions for Safe Use

S8FS-G10024CD-R 数据表(PDF) 29 Page - Omron Electronics LLC

S8FS-G10024CD-R 数据表(HTML) 29 Page - Omron Electronics LLC

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34

数据表下载