Datasheet

www.rohm.com

TSZ02201-0GOG0G200770-1-2

©2015 ROHM Co., Ltd. All rights reserved.

2/37

15.Jul.2016 Rev.002

TSZ22111

• 15 • 001

LM393xxx

LM339xxx

LM2903xxx

LM2901xxx

LM339F, LM2901F

: SOP14

LM339FJ, LM2901FJ

: SOP-J14

LM339FV, LM2901FV

: SSOP-B14

LM339FVJ, LM2901FVJ

: TSSOP-B14J

Absolute Maximum Ratings (TA=25°C)

Parameter

Symbol

Rating

Unit

LM393xxx

LM339xxx

LM2903xxx

LM2901xxx

Supply Voltage

VCC-VEE

+36

V

Power Dissipation

PD

SOP8

0.68

(Note 1,9)

-

0.68

(Note 1,9)

-

W

SOP-J8

0.67

(Note 2,9)

-

0.67

(Note 2,9)

-

SSOP-B8

0.62

(Note 3,9)

-

0.62

(Note 3,9)

-

TSSOP-B8

0.62

(Note 3,9)

-

0.62

(Note 3,9)

-

TSSOP-B8J

0.58

(Note 4,9)

-

0.58

(Note 4,9)

-

MSOP8

0.58

(Note 4,9)

-

0.58

(Note 4,9)

-

SOP14

-

0.56

(Note 5,9)

-

0.56

(Note 5,9)

SOP-J14

-

1.02

(Note 6,9)

-

1.02

(Note 6,9)

SSOP-B14

-

0.87

(Note 7,9)

-

0.87

(Note 7,9)

TSSOP-B14J

-

0.85

(Note 8,9)

-

0.85

(Note 8,9)

Differential Input Voltage

(Note 10)

VID

+36

V

Common-mode Input Voltage range

VICM

(VEE-0.3) to (VEE+36)

V

Input Current

(Note 11)

II

-10

mA

Operating Supply Voltage

Vopr

Single Supply

+3.0 to +32.0

V

Dual Supply

±1.5 to ±16.0

Operating Temperature Range

Topr

-40 to +85

-40 to +125

°C

Storage Temperature Range

Tstg

-55 to +150

°C

Maximum Junction Temperature

Tjmax

+150

°C

(Note 1) Reduce 5.5mW per 1°C above 25°C.

(Note 2) Reduce 5.4mW per 1°C above 25°C.

(Note 3) Reduce 5.0mW per 1°C above 25°C.

(Note 4) Reduce 4.7mW per 1°C above 25°C.

(Note 5) Reduce 4.5mW per 1°C above 25°C.

(Note 6) Reduce 8.2mW per 1°C above 25°C.

(Note 7) Reduce 7.0mW per 1°C above 25°C.

(Note 8) Reduce 6.8mW per 1°C above 25°C.

(Note 9) Mounted on an FR4 glass epoxy PCB 70mm×70mm×1.6mm (Copper foil area less than 3%).

(Note 10) Differential Input Voltage is the voltage difference between the inverting and non-inverting inputs. The input pin voltage is set to more than VEE.

(Note 11) An excessive input current will flow when input voltages of less than VEE-0.6V are applied.

The input current can be set to less than the rated current by adding a limiting resistor.

Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit

between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is

operated over the absolute maximum ratings.

Pin No.

Pin Name

1

OUT2

2

OUT1

3

VCC

4

-IN1

5

+IN1

6

-IN2

7

+IN2

8

-IN3

9

+IN3

10

-IN4

11

+IN4

12

VEE

13

OUT4

14

OUT3

OUT2

OUT1

VCC

-IN1

+IN1

-IN2

+IN2

OUT3

OUT4

VEE

+IN4

-IN4

+IN3

-IN3

－ ＋

－ ＋

－ ＋

1

2

3

4

5

6

7

8

9

10

11

12

13

14

CH1

CH3

CH2

－ ＋

CH4