48

Radial Leaded Aluminum Electrolytic

Capacitors

REF Series

Part No.

Case

Size

Capacitance

(µF)

Rated Voltage

(V)

DF Max.

(%)

Impedance Max. at 20°C @100kHz

(Ω)

100kHz RMS Current

(mA) / 105°C

REF1625471M100*

1625

470

100

8

0.045

1640

REF1825561M100B

1825

560

100

8

0.050

1800

REF1640681M100B

1640

680

100

8

0.034

2200

REF1835681M100B

1835

680

100

8

0.034

2200

REF1840821M100B

1840

820

100

8

0.032

2700

120 Volt

REF0612100M120*

0612

10

120

12

5.500

80

REF0812220M120*

0812

22

120

12

3.500

130

REF0816330M120*

0816

33

120

12

3.000

220

REF1013330M120*

1013

33

120

12

3.000

220

REF1016470M120*

1016

47

120

12

2.500

270

REF1016560M120*

1016

56

120

12

2.200

285

REF1020680M120*

1020

68

120

12

1.800

300

REF1025101M120*

1025

100

120

12

1.500

380

REF1320121M120*

1320

120

120

12

1.300

620

REF1225151M120*

1225

150

120

12

1.000

570

REF1230221M120*

1230

220

120

12

0.800

750

REF1620221M120*

1620

220

120

12

0.600

760

REF1825331M120B

1825

330

120

12

0.420

860

* Used to denote packing type: “K” for Ammo Pack or “B” for Bulk Pack.

DF = When nominal capacitance exceeds 1000μF, add 0.02 to the value above for each 1000μF increase.

All technical data relates to an ambient temperature of +25C. Capacitance and DF are measured at 120Hz, 0.5RMS with DC bias of 2.2 volts. DCL is measured at rated voltage

after 5 minutes

RATED RIPPLE CURRENT MULTIPLIERS (FREQUENCY CORRECTION FACTOR FOR RIPPLE CURRENT)

Freq.(Hz)

Cap.(µF)

120

1K

10K

100K

C < 220

0.40

0.75

0.90

1.00

220 ≤ C < 680

0.50

0.85

0.94

1.00

680 ≤ C < 2200

0.60

0.87

0.95

1.00

2200 ≤ C < 4700

0.75

0.90

0.95

1.00

C ≥ 4700

0.85

0.95

0.98

1.00

QUALIFICATION TABLE

Test

REF Series (Temperature Range -40°C to +105°C)

Condition

Characteristics

Low Temperature

Characteristic

(Max. Impedance Ratio)

120Hz

Rated Voltage (V)

6.3

10

16

25-100

120

Z(-25°C) / Z(20°C)

5

4

3

3

3

Z(-40°C) / Z(20°C)

10

8

5

4

6

Endurance

The following specifications shall be satisfied

when the capacitors are restored to 20°C after

DC voltage plus rated ripple current is applied

for a specified period of time at 105°C.

Visual examination

no visible damage

ΔC/C

≦±25%oftheinitiallimit

DF:

≦200%oftheinitialspecifiedlimit

DCL:

≦Initialspecifiedlimit

Load Life

The following specifications shall be satisfied

when the capacitors are restored to 20°C after

DC voltage plus rated ripple current is applied

for a specified period of time at 105°C.

Diameter (mm)

Load life (hours)

ØD≤6.3

3000

ØD=8

4000

ØD=10

5000

ØD≥12.5

6000

Shelf Life

The following specifications shall be satisfied

when the capacitors are restored to 20°C after

leaving them under no load at 105°C for 1000

hours.

Visual examination

no visible damage

ΔC/C

≦±25%oftheinitiallimit

DF:

≦200%oftheinitialspecifiedlimit

DCL:

≦200%oftheinitialspecifiedlimit

TDS-ALUM-0014 | Rev 0

– aluminum capacitors –

The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or available

online at www.kyocera-avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.