74ALVT16600 datasheet(5/14 Pages) PHILIPS

5 / 14 page

Philips Semiconductors

Product specification

74ALVT16600

2.5V/3.3V 18-bit universal bus transceiver (3-State)

1998 Feb 13

RECOMMENDED OPERATING CONDITIONS

SYMBOL

PARAMETER

2.5V RANGE LIMITS

3.3V RANGE LIMITS

UNIT

SYMBOL

PARAMETER

MIN

MAX

MIN

MAX

UNIT

VCC

DC supply voltage

2.3

2.7

3.0

3.6

Input voltage

5.5

VIH

High-level input voltage

1.7

2.0

VIL

Input voltage

0.7

0.8

IOH

High-level output current

–8

–32

IOL

Low-level output current

IOL

Low-level output current; current duty cycle

≤ 50%; f ≥ 1kHz

∆t/∆v

Input transition rise or fall rate; Outputs enabled

ns/V

Tamb

Operating free-air temperature range

–40

+85

–40

+85

°C

DC ELECTRICAL CHARACTERISTICS (3.3V

"0.3V RANGE)

LIMITS

SYMBOL

PARAMETER

TEST CONDITIONS

Temp = -40

°C to +85°C

UNIT

MIN

TYP1

MAX

VIK

Input clamp voltage

VCC = 3.0V; IIK = –18mA

–0.85

–1.2

VOH

High-level output voltage

VCC = 3.0 to 3.6V; IOH = –100µA

VCC–0.2

VCC

VOH

High-level out ut voltage

VCC = 3.0V; IOH = –32mA

2.0

2.3

VCC = 3.0V; IOL = 100µA

0.07

0.2

VOL

Low–level output voltage

VCC = 3.0V; IOL = 16mA

0.25

0.4

VCC = 3.0V; IOL = 32mA

0.3

0.5

VCC = 3.0V; IOL = 64mA

0.4

0.55

VRST

Power-up output low voltage6

VCC = 3.6V; IO = 1mA; VI = VCC or GND

0.55

VCC = 3.6V; VI = VCC or GND

Control pins

0.1

±1

VCC = 0 or 3.6V; VI = 5.5V

0.1

Input leakage current

VCC = 3.6V; VI = 5.5V

0.1

µA

VCC = 3.6V; VI = VCC

Data pins4

0.5

VCC = 3.6V; VI = 0V

0.1

-5

IOFF

Off current

VCC = 0V; VI or VO = 0 to 4.5V

0.1

±100

µA

Bus Hold current

VCC = 3V; VI = 0.8V

130

IHOLD

Bus Hold current

Data inputs7

VCC = 3V; VI = 2.0V

–75

–140

µA

Data inputs7

VCC = 0V to 3.6V; VCC = 3.6V

±500

IEX

Current into an output in the

High state when VO > VCC

VO = 5.5V; VCC = 3.0V

125

µA

IPU/PD

Power up/down 3-State output

current3

VCC ≤ 1.2V; VO = 0.5V to VCC; VI = GND or VCC

OE = Don’t care

1.0

±100

µA

ICCH

VCC = 3.6V; Outputs High, VI = GND or VCC, IO = 0

0.06

0.1

ICCL

Quiescent supply current

VCC = 3.6V; Outputs Low, VI = GND or VCC, IO = 0

4.0

ICCZ

VCC = 3.6V; Outputs Disabled; VI = GND or VCC, IO = 05

0.06

0.1

∆ICC

Additional supply current per

input pin2

VCC = 3V to 3.6V; One input at VCC–0.6V,

Other inputs at VCC or GND

0.04

0.4

NOTES:

1. All typical values are at VCC = 3.3V and Tamb = 25°C.

2. This is the increase in supply current for each input at the specified voltage level other than VCC or GND

3. This parameter is valid for any VCC between 0V and 1.2V with a transition time of up to 10msec. From VCC = 1.2V to VCC = 3.3V ± 0.3V a

transition time of 100

µsec is permitted. This parameter is valid for Tamb = 25°C only.

4. Unused pins at VCC or GND.

5. ICCZ is measured with outputs pulled up to VCC or pulled down to ground.

6. For valid test results, data must not be loaded into the flip-flops (or latches) after applying power.

7. This is the bus hold overdrive current required to force the input to the opposite logic state.

74ALVT16600 数据表(PDF) 5 Page - NXP Semiconductors

74ALVT16600 数据表(HTML) 5 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14

数据表下载

链接网址

74ALVT16600 数据表(PDF) 5 Page - NXP Semiconductors

74ALVT16600 数据表(HTML) 5 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14

数据表 下载

链接网址

数据表下载