TSOP311.., TSOP313.., TSOP315..

www.vishay.com

Vishay Semiconductors

Rev. 1.7, 02-Aug-2021

2

Document Number: 82493

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Note

• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only

and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification

is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability

PARTS TABLE

AGC

LEGACY, FOR SHORT BURST

REMOTE CONTROLS (AGC1)

NOISY ENVIRONMENTS AND

SHORT BURSTS (AGC3)

VERY NOISY ENVIRONMENTS

AND SHORT BURSTS (AGC5)

Carrier

frequency

30 kHz

TSOP31130

TSOP31330

TSOP31530

33 kHz

TSOP31133

TSOP31333

TSOP31533

36 kHz

TSOP31136

TSOP31336 (1)(6)

TSOP31536

38 kHz

TSOP31138

TSOP31338 (2)(3)(4)(5)

TSOP31538

40 kHz

TSOP31140

TSOP31340

TSOP31540

56 kHz

TSOP31156

TSOP31356

TSOP31556

Package

Cast

Pinning

1 = GND, 2 = VS, 3 = OUT

1 = GND, 2 = VS, 3 = OUT

1 = GND, 2 = VS, 3 = OUT

Dimensions (mm)

10.0 W x 12.5 H x 5.8 D

Mounting

Leaded

Application

Remote control

Best remote control code

(1) MCIR (2) Mitsubishi (3) RECS-80 Code (4) r-map (5) XMP-1, XMP-2 (6) RCMM

Special options

• Low voltage option: www.vishay.com/doc?82382

ABSOLUTE MAXIMUM RATINGS

PARAMETER

TEST CONDITION

SYMBOL

VALUE

UNIT

Supply voltage (pin 2)

VS

-0.3 to +6

V

Supply current (pin 2)

IS

3mA

Output voltage (pin 3)

VO

-0.3 to (VS + 0.3)

V

Output current (pin 3)

IO

5mA

Junction temperature

Tj

100

°C

Storage temperature range

Tstg

-25 to +85

°C

Operating temperature range

Tamb

-25 to +85

°C

Power consumption

Tamb

≤ 85 °C

Ptot

10

mW

Soldering temperature

t

≤ 10 s, 1 mm from case

Tsd

260

°C

ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)

PARAMETER

TEST CONDITION

SYMBOL

MIN.

TYP.

MAX.

UNIT

Supply current (pin 2)

Ev = 0, VS = 3.3 V

ISD

0.27

0.35

0.45

mA

Ev = 40 klx, sunlight

ISH

-0.45

-

mA

Supply voltage

VS

2.5

-

5.5

V

Transmission distance

Ev = 0, test signal see Fig. 1,

IR diode TSAL6200, IF = 50 mA

d-

24

-

m

Output voltage low (pin 3)

IOSL = 0.5 mA, Ee = 0.7 mW/m2,

test signal see Fig. 1

VOSL

-

-

100

mV

Minimum irradiance

Pulse width tolerance:

tpi - 5/fo < tpo < tpi + 6/fo, test signal

see Fig. 1

Ee min.

-

0.12

0.25

mW/m2

Maximum irradiance

tpi - 5/fo < tpo < tpi + 6/fo, test signal

see Fig. 1

Ee max.

30

-

-

W/m2

Directivity

Angle of half transmission

distance

ϕ1/2

-± 45

-

°