TSOP932..P10TR, TSOP934..P10TR

www.vishay.com

Vishay Semiconductors

Rev. 1.1, 05-Aug-2021

2

Document Number: 82874

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Notes

• 30 kHz and 33 kHz only available on written request

• See datasheet for TSOP936..P10TR for preferred devices for (3)(4)(5)(6)(11)

Note

• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only

and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification

is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability

PARTS TABLE

AGC

BASIC NOISE SUPPRESSION

(AGC2)

ENHANCED NOISE SUPPRESSION

(AGC4)

Carrier frequency

30 kHz

TSOP93230P10TR

TSOP93430P10TR

33 kHz

TSOP93233P10TR

TSOP93433P10TR

36 kHz

TSOP93236P10TR

TSOP93436P10TR (2)(7)

38 kHz

TSOP93238P10TR

TSOP93438P10TR (10)

40 kHz

TSOP93240P10TR (12)

TSOP93440P10TR

56 kHz

TSOP93256P10TR (1)

TSOP93456P10TR (8)(9)

Package

Minimold

Pinning

1 = OUT, 2 = GND, 3 = VS

Dimensions (mm)

5.4 W x 6.35 H x 4.9 D

Mounting

Leaded

Application

Remote control

Best choice for

(1) Cisco (2) MCIR (3) Mitsubishi (4) NEC (5) Panasonic (6) RC-5 (7) RC-6

(8) RCA (9) r-step (10) Sejin 4PPM (11) Sharp (12) Sony

Special options

• Narrow optical filter: www.vishay.com/doc?81590

• Wide optical flter: www.vishay.com/doc?82726

ABSOLUTE MAXIMUM RATINGS

PARAMETER

TEST CONDITION

SYMBOL

VALUE

UNIT

Supply voltage

VS

-0.3 to +3.6

V

Supply current

IS

3mA

Output voltage

VO

-0.3 to (VS + 0.3)

V

Output current

IO

5mA

Junction temperature

Tj

100

°C

Storage temperature range

Tstg

-25 to +85

°C

Operating temperature range

Tamb

-25 to +85

°C

Power consumption

Tamb

≤ 85 °C

Ptot

10

mW

Soldering temperature

t

≤ 10 s, 1 mm from case

Tsd

260

°C

ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)

PARAMETER

TEST CONDITION

SYMBOL

MIN.

TYP.

MAX.

UNIT

Supply current

Ev = 0, VS = 3.3 V

ISD

0.25

0.37

0.45

mA

Ev = 40 klx, sunlight

ISH

-0.50-

mA

Supply voltage

VS

2.0

-

3.6

V

Transmission distance

Ev = 0, test signal see Fig. 1,

IR diode TSAL6200, IF = 50 mA

d-

30

-

m

Output voltage low

IOSL = 0.5 mA, Ee = 0.7 mW/m2,

test signal see Fig. 1

VOSL

-

-

100

mV

Minimum irradiance

Test signal: NEC code

Ee min.

-

0.08

0.15

mW/m2

Maximum irradiance

tpi - 4/f0 < tpo < tpi + 4/f0,

test signal see Fig. 1

Ee max.

30

-

-

W/m2

Directivity

Angle of half transmission

distance

ϕ1/2

-± 45

-

°