TSOP953.., TSOP955..

www.vishay.com

Vishay Semiconductors

Rev. 1.3, 13-Apr-2022

2

Document Number: 82838

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Note

• 30 kHz and 33 kHz only available on written request

Note

• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only

and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification

is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability

PARTS TABLE

AGC

ENHANCED NOISE SUPPRESSION

(AGC3)

MAXIMIZED NOISE SUPPRESSION

(AGC5)

Carrier frequency

30 kHz

TSOP95330

TSOP95530

33 kHz

TSOP95333

TSOP95533

36 kHz

TSOP95336 (1)

TSOP95536

38 kHz

TSOP95338 (2)(4)

TSOP95538

40 kHz

TSOP95340

TSOP95540

56 kHz

TSOP95356

TSOP95556 (3)

Package

Heimdall

Pinning

1, 4 = GND, 2 = VS, 3 = OUT

Dimensions (mm)

6.8 W x 3.0 H x 3.2 D

Mounting

SMD

Application

Remote control

Best choice for

(1) RCMM (2) RECS-80 Code (3) r-map (4) XMP-1, XMP-2

Special options

• Extended temperature range: www.vishay.com/doc?82738

• Narrow optical filter: www.vishay.com/doc?81590

• Wide optical flter: www.vishay.com/doc?82726

ABSOLUTE MAXIMUM RATINGS

PARAMETER

TEST CONDITION

SYMBOL

VALUE

UNIT

Supply voltage

VS

-0.3 to +3.6

V

Supply current

IS

3mA

Output voltage

VO

-0.3 to (VS + 0.3)

V

Output current

IO

5mA

Junction temperature

Tj

100

°C

Storage temperature range

Tstg

-25 to +85

°C

Operating temperature range

Tamb

-25 to +85

°C

Power consumption

Tamb

≤ 85 °C

Ptot

10

mW

ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)

PARAMETER

TEST CONDITION

SYMBOL

MIN.

TYP.

MAX.

UNIT

Supply current

Ev = 0, VS = 3.3 V

ISD

0.25

0.37

0.45

mA

Ev = 40 klx, sunlight

ISH

-0.50-

mA

Supply voltage

VS

2.0

-

3.6

V

Transmission distance

Ev = 0, test signal see Fig. 1,

IR diode TSAL6200, IF = 50 mA

d-

24

-

m

Output voltage low

IOSL = 0.5 mA, Ee = 0.7 mW/m2,

test signal see Fig. 1

VOSL

-

-

100

mV

Minimum irradiance

Test signal: XMP code

Ee min.

-

0.16

0.35

mW/m2

Test signal: NEC code

Ee min.

-

0.12

0.30

mW/m2

Maximum irradiance

tpi - 3.0/f0 < tpo < tpi + 3.5/f0,

test signal see Fig. 1

Ee max.

30

-

-

W/m2

Directivity

Angle of half transmission distance

ϕ1/2

-± 50

-

°