For the most current data and application support visit www.artesyn.com/powergroup/products.htm

Notes

1

Free air convection.

Multiple output units: maximum continuous output power not to exceed

80W.

Single output units: maximum continuous output power not to exceed;

75W on –9905; 76.8W on –9912,-9924, and –9917.

2

150LFM forced air cooling from L4 side.

Multiple output units: maximum continuous output power not to exceed

105W.

Single output units: maximum continuous output power not to exceed

110W for all models.

3

300LFM forced air cooling from L4 side.

Multiple output units: maximum continuous output power not to exceed

110W.

Single output units: maximum continuous output power not to exceed

110W for all models.

4

Peak output current lasting less than 30 seconds with duty cycle less

than 5%. During peak loading, output voltage may exceed total

regulation limits.

5

Figure is peak-to-peak for convection power rating. Output noise

measurements are made across a 20MHz bandwidth using a 6” twisted

pair, terminated with a 10µF electrolytic capacitor and a 0.1µF ceramic

capacitor.

N

6

Minimum load required for correct start-up and operation on single

outputs and on main output of multiple versions. Failure to observe

minimum load on main output will not allow the supply to start-up

correctly. Some electronic test loads have a large delay time before they

start drawing current even though the voltage from the supply is present.

During this time delay, there is no load on the output and as a result, the

supply cannot start-up properly and maintain its correct output voltage.

In these instances, a dummy resistive load across the output may be

necessary to load the output of the supply until the test load can function

correctly and draw the intended minimum load. Minimum load required

on auxiliary outputs to maintain regulation.

7

For models NLP110-9908 and NLP110-9995, the 12V output is floating.

For -12V output, pin 11 on J2 has to be connected to Return making pin

12 the -12V output

8

Three orthogonal axes, random vibration 10 minutes for each axes, 2.4G

rms 5Hz to 500Hz.

9

when making thermal measurements.

equipment and must not be operated as a stand alone product.

supply mounted on a grounded metal sheet extending 1 inch beyond

each edge, using an unshielded cable. No external filtering required

during conducted emissions testing but some applications may require

additional filtering to achieve system compliance. A line choke, (AC input

cords looped twice through an EMI suppression toroid) was used during

radiated emissions testing. Considerable radiated testing in 1U six-sided

boxes has shown that units can meet level B in typical systems.

Application support is available from the factory to assist with EMI

compliance.

inches) in the end use product.

NLP110 Medical Series

Single and triple output

LOW TO MEDIUM POWER AC/DC POWER SUPPLIES

80-110W AC/DC Universal Input Switch Mode Power Supplies

2

www.artesyn.com

File Name: NLP110M.PDF Rev: 13 Dec 2002

International Safety Standard Approvals

VDE0750/IEC60601-1 and EN60601-1

UL2601-1 and C22.2 No. 601.1-M90.

OUTPUT

OUTPUT CURRENT

TOTAL

MODEL

VOLTAGE

REGULATION

NUMBERS

+5V

0.5A

15A

22A

22A

22A

50mV

±2.0%

NLP110-9905

+12V

0.3A

6.4A

9.2A

9.2A

11.5A

120mV

±2.0%

NLP110-9912

+48V

0A

1.6A

2.3A

2.3A

2.5A

240mV

±2.0%

NLP110-9917

+24V

0.2A

3.2A

4.6A

4.6A

6.0A

240mV

±2.0%

NLP110-9924

+5V (A)

0.5A

13A

16A

18A

18A

50mV

±2.0%

NLP110-9993

+3.3V (B)

0.2A

13A

16A

20A

20A

50mV

±2.0%

+12V

0A

0.65A

1.0A

1A

1.0A

120mV

±5.0%

+3.3V (A)

0.5A

13A

16A

20A

22A

50mV

±2.0%

NLP110-9994

+2.5V (B)

0.1A

13A

16A

20A

22A

50mV

±2.0%

+12V

0A

0.65A

1.0A

1A

1.0A

120mV

±5.0%

+12V (A)

0.2A

6.5A

8.5A

8.5A

10A

1200mV

±2.0%

+3.3V (B)

0.5A

13A

16A

20A

22A

50mV

±2.0%

-12V

0A

0.65A

1.0A

1A

1.0A

120mV

±5.0%

+12V (A)

0.2A

6.5A

8.5A

8.5A

10A

120mV

±2.0%

+5V (B)

0.2A

13A

16A

18A

22A

50mV

±2.0%

-12V

0A

0.65A

1.0A

1A

1.0A

120mV

±5.0%