LPS22HH datasheet(27/59 Pages) STMICROELECTRONICS

27 / 59 page

DocID030890 Rev 2

27/59

LPS22HH

Digital interfaces

7.2.1

I²C operation

The transaction on the bus is started through a START (ST) signal. A start condition is

defined as a HIGH-to-LOW transition on the data line while the SCL line is held HIGH. After

the master has transmitted this, the bus is considered busy. The next data byte transmitted

after the start condition contains the address of the slave in the first 7 bits and the eighth bit

tells whether the master is receiving data from the slave or transmitting data to the slave.

When an address is sent, each device in the system compares the first seven bits after a start

condition with its address. If they match, the device considers itself addressed by the master.

The 7-bit slave address (SAD) associated to the LPS22HH is 101110xb. The SDO/SA0 pad

can be used to modify the less significant bit of the device address. If the SA0 pad is

connected to voltage supply, LSb is ‘1’ (7-bit address 1011101b=5Dh), otherwise if the SA0

pad is connected to ground, the LSb value is ‘0’ (7-bit address 1011100b=5Ch). This

solution permits connecting and addressing two different LPS22HH devices to the same I²C

lines.

Data transfer with acknowledge is mandatory. The transmitter must release the SDA line

during the acknowledge pulse. The receiver must then pull the data line LOW so that it

remains stable low during the HIGH period of the acknowledge clock pulse. A receiver which

has been addressed is obliged to generate an acknowledge after each byte of data received.

The I²C embedded inside the ASIC behaves like a slave device and the following protocol

must be adhered to. After the start condition (ST) a slave address is sent, once a slave

acknowledge has been returned (SAK), an 8-bit sub-address will be transmitted (SUB): the

7 LSB represent the actual register address while the MSB has no meaning. The

IF_ADD_INC bit in CTRL_REG2 (11h) enables sub-address auto increment (IF_ADD_INC

is '1' by default), so if IF_ADD_INC = '1' the SUB (sub-address) will be automatically

increased to allow multiple data read/write.

The slave address is completed with a Read/Write bit. If the bit is ‘1’ (Read), a repeated

START (SR) condition must be issued after the two sub-address bytes; if the bit is ‘0’ (Write)

the master will transmit to the slave with direction unchanged. Table 11 explains how the

SAD+read/write bit pattern is composed, listing all the possible configurations.

Table 11. SAD+Read/Write patterns

Command

SAD[6:1]

SAD[0] = SA0

R/W

SAD+R/W

Read

101110

10111001 (B9h)

Write

101110

10111000 (B8h)

Read

101110

10111011 (BBh)

Write

101110

10111010 (BAh)

Table 12. Transfer when master is writing one byte to slave

Master

SAD + W

SUB

DATA

Slave

SAK

LPS22HH 数据表(PDF) 27 Page - STMicroelectronics

LPS22HH 数据表(HTML) 27 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

数据表下载

链接网址

LPS22HH 数据表(PDF) 27 Page - STMicroelectronics

LPS22HH 数据表(HTML) 27 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59

数据表 下载

链接网址

数据表下载