HCS05MS

FN3557 Rev 1.00

Page 4 of 7

September 1995

TABLE 6. APPLICABLE SUBGROUPS

CONFORMANCE GROUPS

METHOD

GROUP A SUBGROUPS

READ AND RECORD

Initial Test (Preburn-In)

100%/5004

1, 7, 9

ICC, IOL, IOZH

Interim Test I (Postburn-In)

100%/5004

1, 7, 9

ICC, IOL, IOZH

Interim Test II (Postburn-In)

100%/5004

1, 7, 9

ICC, IOL/H

PDA

100%/5004

1, 7, 9, Deltas

Interim Test III (Postburn-In)

100%/5004

1, 7, 9

ICC, IOL, IOZH

PDA

100%/5004

1, 7, 9, Deltas

Final Test

100%/5004

2, 3, 8A, 8B, 10, 11

Group A (Note 1)

Sample/5005

1, 2, 3, 7, 8A, 8B, 9, 10, 11

Group B

Subgroup B-5

Sample/5005

1, 2, 3, 7, 8A, 8B, 9, 10, 11, Deltas

Subgroups 1, 2, 3, 9, 10, 11

Subgroup B-6

Sample/5005

1, 7, 9

Group D

Sample/5005

1, 7, 9

NOTE:

1. Alternate Group A testing in accordance with Method 5005 of MIL-STD-883 may be exercised.

TABLE 7. TOTAL DOSE IRRADIATION

CONFORMANCE

GROUPS

METHOD

TEST

READ AND RECORD

PRE RAD

POST RAD

PRE RAD

POST RAD

Group E Subgroup 2

5005

1, 7, 9

Table 4

1, 9

Table 4 (Note 1)

NOTE:

1. Except FN test which will be performed 100% Go/No-Go.

TABLE 8. STATIC AND DYNAMIC BURN-IN TEST CONNECTIONS

OPEN

GROUND

VCC = 6V

 0.5V

1/2 VCC = 3V

 0.5V

OSCILLATOR

50kHz

25kHz

STATIC BURN-IN I TEST CONDITIONS (Note 1)

-

1, 3, 5, 7, 9, 11, 13

2, 4, 6, 8, 10, 12, 14

-

-

-

STATIC BURN-IN II TEST CONNECTIONS (Note 1)

2, 4, 6, 8, 10, 12

7

1, 3, 5, 9, 11, 13, 14

-

-

-

DYNAMIC BURN-IN I TEST CONNECTIONS (Note 2)

-

7

14

2, 4, 6, 8, 10, 12

1, 3, 5, 9, 11, 13

-

NOTES:

1. Each pin except VCC and GND will have a series resistor of 10K

  5%.

2. Each pin except VCC and GND will have a series resistor of 1K

  5%.

TABLE 9. IRRADIATION TEST CONNECTIONS

FUNCTION

OPEN

GROUND

VCC = 5V

 0.5V

Irradiation Circuit

(Note 1)

2, 4, 6, 8, 10, 12

7

1, 3, 5, 9, 11, 13, 14

NOTE: Each pin except VCC and GND will have a resistor of 47K

  5% for irradiation testing. Group E, Subgroup 2, sample

size is 4 dice/wafe,r 0 failures.