HCS193MS

FN3065 Rev 1.00

Page 6 of 9

September 1995

TABLE 5. BURN-IN AND OPERATING LIFE TEST, DELTA PARAMETERS (+25oC)

PARAMETER

GROUP B

SUBGROUP

DELTA LIMIT

ICC

5

12

A

IOL/IOH

5

-15% of 0 Hour

TABLE 6. APPLICABLE SUBGROUPS

CONFORMANCE GROUPS

METHOD

GROUP A SUBGROUPS

READ AND RECORD

Initial Test (Preburn-In)

100%/5004

1, 7, 9

ICC, IOL/H

Interim Test I (Postburn-In)

100%/5004

1, 7, 9

ICC, IOL/H

Interim Test II (Postburn-In)

100%/5004

1, 7, 9

ICC, IOL/H

PDA

100%/5004

1, 7, 9, Deltas

Interim Test III (Postburn-In)

100%/5004

1, 7, 9

ICC, IOL/H

PDA

100%/5004

1, 7, 9, Deltas

Final Test

100%/5004

2, 3, 8A, 8B, 10, 11

Group A (Note 1)

Sample/5005

1, 2, 3, 7, 8A, 8B, 9, 10, 11

Group B

Subgroup B-5

Sample/5005

1, 2, 3, 7, 8A, 8B, 9, 10, 11, Deltas

Subgroups 1, 2, 3, 9, 10, 11,

(Note 2)

Subgroup B-6

Sample/5005

1, 7, 9

Group D

Sample/5005

1, 7, 9

NOTES:

1. Alternate Group A testing in accordance with method 5005 of MIL-STD-883 may be exercised.

2. Table 5 parameters only.

TABLE 7. TOTAL DOSE IRRADIATION

CONFORMANCE

GROUPS

METHOD

TEST

READ AND RECORD

PRE RAD

POST RAD

PRE RAD

POST RAD

Group E Subgroup 2

5005

1, 7, 9

Table 4

1, 9

Table 4 (Note 1)

NOTE: 1. Except FN test which will be performed 100% Go/No-Go.

TABLE 8. DYNAMIC BURN-IN TEST CONNECTIONS

OPEN

GROUND

1/2 VCC = 3V

 0.5V

VCC = 6V

 0.5V

OSCILLATOR

50kHz

25kHz

STATIC BURN-IN I TEST CONNECTIONS (Note 1)

2, 3, 6, 7, 12, 13

1, 4, 5, 8 - 11, 14, 15

-

16

-

-

STATIC BURN-IN II TEST CONNECTIONS (Note 1)

2, 3, 6, 7, 12, 13

8

-

1, 4, 5, 9 - 11, 14 - 16

-

-

DYNAMIC BURN-IN TEST CONNECTIONS (Note 2)

-

1, 8 - 11, 14, 15

2, 3, 6, 7, 12, 13

4, 11, 16

5

-

NOTES:

1. Each pin except VCC and GND will have a resistor of 10K

  5% for static burn-in.

2. Each pin except VCC and GND will have a resistor of 1K

  5% for dynamic burn-in.

TABLE 9. IRRADIATION TEST CONNECTIONS

OPEN

GROUND

VCC = 5V

 0.5V

2, 3, 6, 7, 12, 13

8

1, 4, 5, 9 - 11, 14 - 16

NOTE: Each pin except VCC and GND will have a resistor of 47K

  5% for irradiation testing. Group

E, Subgroup 2, sample size is 4 dice/wafer 0 failures.