Filterless High Efficiency Mono 1.4 W

Class-D Audio Amplifier

Preliminary Technical Data

SSM2301

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibilityis assumedbyAnalogDevicesforitsuse,norforanyinfringements of patents or other

rightsofthirdpartiesthatmayresultfromitsuse.Specificationssubjecttochangewithoutnotice.No

license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

Trademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781.329.4700

www.analog.com

Fax: 781.461.3113

©2006 Analog Devices, Inc. All rights reserved.

FEATURES

Filterless Class-D amplifier with built-in output stage

1.4 W into 8 Ω at 5.0 V supply with less than 1% THD

85% efficiency at 5.0 V, 1.4 W into 8 Ω speaker

Better than 98 dB SNR (signal-to-noise ratio)

Single-supply operation from 2.5 V to 5.0 V

20 nA ultralow shutdown current

Short-circuit and thermal protection

Available in 8-lead, 3 mm × 3 mm LFCSP

Pop-and-click suppression

Built-in resistors reduce board component count

Fixed and user-adjustable gain configurations

APPLICATIONS

Mobile phones

MP3 players

Portable gaming

Portable electronics

Educational toys

GENERAL DESCRIPTION

The SSM2301 is a fully integrated, high efficiency, Class-D audio

amplifier. It is designed to maximize performance for mobile

phone applications. The application circuit requires a minimum

of external components and operates from a single 2.5 V to 5.0 V

supply. It is capable of delivering 1.4 W of continuous output

power with less than 1% THD + N driving an 8 Ω load from a

5.0 V supply.

The SSM2301 features a high efficiency, low noise modulation

scheme that does not require any external LC output filters. The

modulation continues to provide high efficiency even at low

output power. It operates with 85% efficiency at 1.4 W into 8 Ω

from a 5.0 V supply and has a signal-to-noise ratio (SNR) that is

better than 93 dB. Spread-spectrum modulation is used to

provide lower EMI-radiated emissions compared with other

Class-D architectures.

The SSM2301 has a micropower shutdown mode with a

maximum shutdown current of 30 nA. Shutdown is enabled by

applying a logic low to the SD pin.

The device also includes pop-and-click suppression circuitry.

This minimizes voltage glitches at the output during turn-on

and turn-off, thus reducing audible noise on activation and

deactivation.

The fully differential input of the SSM2301 provides excellent

rejection of common-mode noise on the input. Input coupling

capacitors can be omitted if the dc input common-mode voltage

The SSM2301 also has excellent rejection of power supply noise,

including noise caused by GSM transmission bursts and RF

rectification. PSRR is typically 63 dB at 217 Hz.

The gain can be set to 6 dB or 12 dB utilizing the gain control

also be adjusted externally by using an external resistor.

The SSM2301 is specified over the comercial temperature range

(−40°C to +85°C). It has built-in thermal shutdown and output

short-circuit protection. It is available in an 8-lead, 3 mm × 3 mm

lead-frame chip scale package (LFCSP).

FUNCTIONAL BLOCK DIAGRAM

SHUTDOWN

GAIN

CONTROL

FET

DRIVER

MODULATOR

0.1µF

VDD

GND

OSCILLATOR

POP/CLICK

SUPRESSION

OUT+

OUT–

BIAS

IN+

VBATT

2.5V TO 5.0V

IN–

GAIN

10µF

SD

AUDIO IN–

AUDIO IN+

SSM2301

Figure 1.

Rev. PrH