Energy Metering IC with Integrated

Oscillator and No-Load Indication

ADE7769

Rev. A

Information furnished by Analog Devices is believed to be accurate and reliable.

However, no responsibility is assumed by Analog Devices for its use, nor for any

infringements of patents or other rights of third parties that may result from its use.

Specifications subject to change without notice. No license is granted by implication

or otherwise under any patent or patent rights of Analog Devices. Trademarks and

registered trademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Tel: 781.329.4700

www.analog.com

Fax: 781.461.3113

© 2005 Analog Devices, Inc. All rights reserved.

FEATURES

On-chip oscillator as clock source

High accuracy, supports 50 Hz/60 Hz IEC62053-21

Less than 0.1% error over a dynamic range of 500 to 1

Supplies average real power on frequency outputs F1 and F2

High frequency output CF calibrates and supplies

instantaneous real power

CF output remains logic high when ADE7769 is under

no-load threshold

Logic output REVP indicates a potential miswiring or

negative power

Direct drive for electromechanical counters and 2-phase

stepper motors (F1 and F2)

Proprietary ADCs and DSPs provide high accuracy over

large variations in environmental conditions and time

On-chip power supply monitoring

On-chip creep protection (no-load threshold)

On-chip reference 2.45 V (20 ppm/°C typical) with external

overdrive capability

Single 5 V supply, low power (20 mW typical)

Low cost CMOS process

GENERAL DESCRIPTION

It is a pin reduction version of the ADE7755 with an enhanced,

precise oscillator circuit that serves as a clock source to the chip.

The ADE7769 eliminates the cost of an external crystal or

resonator, thus reducing the overall cost of a meter built with

this IC. The chip directly interfaces with the shunt resistor.

The ADE7769 specifications surpass the accuracy require-

ments of the IEC62053-21 standard. The AN-679 Application

Note can be used as a basis for a description of an IEC61036

(equivalent to IEC62053-21) low cost, watt-hour meter

reference design.

The only analog circuitry used in the ADE7769 is in the Σ-Δ

ADCs and reference circuit. All other signal processing, such as

multiplication and filtering, is carried out in the digital domain.

This approach provides superior stability and accuracy over

time and extreme environmental conditions.

The ADE7769 supplies average real power information on the

low frequency outputs, F1 and F2. These outputs can be used to

directly drive an electromechanical counter or interface with an

MCU. The high frequency CF logic output, ideal for calibration

purposes, provides instantaneous real power information.

The ADE7769 includes a power supply monitoring circuit on

falls below 4 V, the ADE7769 also remains inactive and the F1,

F2, and CF outputs are in their nonactive modes.

Internal phase matching circuitry ensures that the voltage and

current channels are phase matched, while the HPF in the

current channel eliminates dc offsets. An internal no-load

threshold ensures that the ADE7769 does not exhibit creep

when no load is present. During a no-load condition, the CF

pin stays logic high.

The ADE7769 has a 16-lead, narrow body SOIC package.

FUNCTIONAL BLOCK DIAGRAM

MULTIPLIER

REVP

V2P

V2N

V1P

RCLKIN

F1

F2

CF

SCF

S0

S1

PHASE

CORRECTION

4k

Ω

...110101...

SIGNAL

PROCESSING

BLOCK

POWER

SUPPLY MONITOR

Σ-Δ

ADC

V1N

ADE7769

...11011001...

2.5V

REFERENCE

AGND

DGND

Φ

INTERNAL

OSCILLATOR

Σ-Δ

ADC

LPF

HPF

+

+

1

6

13

7

11

8

10

12

14

16

15

9

DIGITAL-TO-FREQUENCY

CONVERTER

2

3

4

5

Figure 1.