| 数据搜索系统,热门电子元器件搜索 |
|
ICS1893CF 数据表(PDF) 50 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
ICS1893CF 数据表(HTML) 50 Page - Renesas Technology Corp |
|
50 / 127 page ![]() ICS1893CF, Rev. K, 05/13/10 May, 2010 50 Chapter 7 Management Register Set ICS1893CF Data Sheet - Release Copyright © 2009, Integrated Device Technology, Inc. All rights reserved. 7.3 Register 1: Status Register Table 7-6 lists the Status Register bits. These 16 bits of data provide an interface between the ICS1893CF and an STA. There are two types of status bits: some report the capabilities of the port, and some indicate the state of signals used to monitor internal circuits. The STA accesses the Status Register using the Serial Management Interface. During a reset, the ICS1893CF initializes the Status Register bits to pre-defined, default values. Note: For an explanation of acronyms used in Table 7-5, see Chapter 1, “Abbreviations and Acronyms”. † As per the IEEE Std 802.3u, during any write operation to any bit in this register, the STA must write the default value to all Reserved bits. 7.3.1 100Base-T4 (bit 1.15) The STA reads this bit to learn if the ICS1893CF can support 100Base-T4 operations. Bit 1.15 of the ICS1893CF is permanently set to logic zero, which informs an STA that the ICS1893CF cannot support 100Base-T4 operations. Table 7-6. Status Register (Register 1 [0x01]) Bit Definition When Bit = 0 When Bit = 1 Ac- cess SF De- fault Hex 1.15 100Base-T4 Always 0. (Not supported.) N/A RO – 0 7 1.14 100Base-TX full duplex Mode not supported Mode supported CW – 1 1.13 100Base-TX half duplex Mode not supported Mode supported CW – 1 1.12 10Base-T full duplex Mode not supported Mode supported CW – 1 1.11 10Base-T half duplex Mode not supported Mode supported CW – 1 8 1.10 IEEE reserved Always 0 N/A CW – 0† 1.9 IEEE reserved Always 0 N/A CW – 0† 1.8 IEEE reserved Always 0 N/A CW – 0† 1.7 IEEE reserved Always 0 N/A CW – 0† 0 1.6 MF Preamble suppression PHY requires MF Preambles PHY does not require MF Preambles RO – 0 1.5 Auto-Negotiation complete Auto-Negotiation is in process, if enabled Auto-Negotiation is completed RO LH 0 1.4 Remote fault No remote fault detected Remote fault detected RO LH 0 1.3 Auto-Negotiation ability N/A Always 1: PHY has Auto-Negotiation ability RO – 1 9 1.2 Link status Link is invalid/down Link is valid/established RO LL 0 1.1 Jabber detect No jabber condition Jabber condition detected RO LH 0 1.0 Extended capability N/A Always 1: PHY has extended capabilities RO – 1 |
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |