L4863-S16-R datasheet(3/10 Pages) UTC

3 / 10 page

L4863

CMOS IC

UNISONICTECHNOLOGIESCO.,LTD

3 of 10

www.unisonic.com.tw

QW-R107-050,A

ABSOLUTE MAXIMUM RATING

PARAMETER

SYMBOL

RATINGS

UNIT

Supply Voltage

VDD

6.0

Recommended Supply Voltage Range

VDD

2.0 ~ 5.5

Input Voltage

VIN

-0.3 ~ VDD+0.3

Power Dissipation

Internally limited

Junction Temperature

+125

℃

Operating Temperature

TOPR

-40 ~ +85

℃

Storage Temperature

TSTG

-65 ~ +150

℃

Note Absolute maximum ratings are those values beyond which the device could be permanently damaged.

Absolute maximum ratings are stress ratings only and functional device operation is not implied.

ELECTRICAL CHARACTERISTICS (Notes 1)(VDD=5V, Ta =25 ,

℃

unless otherwise specified)

PARAMETER

SYMBOL

TEST CONDITIONS

MIN TYP MAX UNIT

FOR ENTIRE IC

Supply Voltage

VDD

5.5

VIN=0V, IOUT=0A, HP-IN=0V

11.5

Quiescent Power Supply Current

(Note 2)

IDD

VIN=0V, IOUT=0A, HP-IN=4V

5.8

Shutdown Current

ISD

VDD applied to the SHUTDOWN pin

0.7

μA

High

VIH

Headphone Input Voltage

Low

VIL

0.8

FOR BRIDGED-MODE OPERATION

Output Offset Voltage

VO(OFF) VIN=0V

RL=3Ω

2.5

THD=1%, f=1kHz

RL=4Ω

2.2

RL=3Ω

3.2

HTSSOP-20

THD+N=10%, f=1kHz

RL=4Ω

2.7

THD=1%, f=1kHz

RL=8Ω

1.0

1.1

THD+N=10%, f=1kHz

RL=8Ω

1.5

Output Power

(measured at the device

terminals)

SOP/DIP

POUT

THD+N=1%, f=1kHz, RL=32Ω

0.34

HTSSOP-20

RL=4Ω, POUT=2W

0.3

Total

Harmonic

Distortion + Noise

SOP/DIP

THD+N

20Hz≤f≤20kHz,

AVD=2

RL=8Ω, POUT=1W

0.3

Power Supply Rejection Ratio

PSRR

VDD=5V, VRIPPLE=200mVRMS, RL=8Ω,

CB=1.0μF

Channel Separation

XTALK

f=1kHz, CB=1.0μF

Signal To Noise Ratio

SNR

VDD=5V, POUT=1.1W, RL=8Ω

FOR SINGLE-ENDED OPERATION

Output Offset Voltage

VO(OFF) VIN=0V

THD=0.5%, f=1kHz, RL=32Ω

THD+N=1%, f=1kHz, RL=8Ω

340

Output Power

POUT

THD+N=10%, f=1kHz, RL=8Ω

440

Total Harmonic Distortion + Noise

THD+N

AV=-1, POUT=75mW,20Hz≤f≤20kHz,

RL=32Ω

0.2

Power Supply Rejection Ratio

PSRR CB=1.0μF, VRIPPLE=200mVRMS, f=1kHz

Channel Separation

XTALK

f=1kHz, CB=1.0μF

Signal To Noise Ratio

SNR

VDD=5V, POUT=340mW, RL=8Ω

Note:1. All voltages are measured with respect to the ground (GND) pins, unless otherwise specified.

2. Depends on the offset voltage when a practical load is connected to the amplifier.

3. When driving 3Ω or 4Ω and operating on a 5V supply, the HTSSOP-20 package must be mounted to the

circuit board that has a minimum of 2.5 in

2 of exposed, uninterrupted copper area connected to the

exposed-DAP.

L4863-S16-R 数据表(PDF) 3 Page - Unisonic Technologies

L4863-S16-R 数据表(HTML) 3 Page - Unisonic Technologies

Html Pages

1 2 3 4 5 6 7 8 9 10

数据表下载