UPC271, 311

R03DS0151EJ0100 Rev.1.00

Page 2 of 8

2019.10.1

ABSOLUTE MAXIMUM RATING (TA = 25

C)

PARAMETER

SYMBOL

μPC271G2

μPC311G2

UNIT

Power Supply Voltage Note1

V + - V -

-0.3 to +36

V

Differential Input Voltage

VID

±30

V

Input Voltage Note2

VI

V - -0.3 to V + +0.3

V

Output to Negative Supply Voltage Note3

VO – V -

-0.3 to +40

V

Ground to Negative Supply Voltage Note3

VGND – V -

-0.3 to +30

V

Total Power Dissipation Note4

PT

440

mW

Output Short Circuit Duration Note5

10

s

Operating Ambient Temperature

TA

-40 to +85

-20 to +80

C

Storage Temperature

Tstg

-55 to +125

C

[Note] 1. Note that reverse connections of the power supply may damage the ICs.

2. The input terminal must be applied within the input voltage range to avoid deterioration or damaging the device

characteristic. Do not exceed the ratings including during transient state such as ON/OFF, etc. The Comparator

input voltage must operate within the electrical characteristics range of input common-mode voltage.

3. The output terminal and GND terminal must be apply within the output voltage range to avoid deteriorating or

damaging the device characteristic. The GND terminal must be less than V+. Do not exceed the ratings including

during transient state such as ON/OFF, etc.

4. This is the value at TA ≤ +25

C. De-rate value at -4.4 mW/C when TA > 25 C.

5. Pay attention to output terminal current and GND terminal current. Please use the total loss and the de-rating

value from Note 4.

RECOMMENDED OPERATING CONDITIONS

PARAMETER

SYMBOL

MIN.

TYP.

MAX.

UNIT

Power Supply Voltage (Dual Supply)

V ±

±4

±16

V

Power Supply Voltage (V - = GND)

V +

+5

+32

V

ELECTRICAL CHARACTERISTICS (V ± = ±15 V, TA = 25

C)

PARAMETER

SYMBOL

MIN.

TYP.

MAX.

UNIT

TEST CONDITION

Input Offset Voltage Note6

VIO

±2.0

±7.5

mV

V + - V - = 5 V to 30 V, RS ≤ 50 kΩ

Input Offset Current Note6

IIO

±6.0

±50

nA

V + - V - = 5 V to 30 V

Input Bias Current

IB

100

250

nA

V + - V - = 5 V to 30 V

Voltage Gain

AV

200000

RL = 1.0 kΩ

Pulse Response Time

200

ns

Input step 100 mV,

Overdrive 5 mV

Output Saturation Voltage

VOL

0.75

1.5

V

VI ≤ -10 mV, IO = 50 mA

Strobe Operating Current

3.0

mA

Output Leakage Current

IO LEAK

0.2

50

nA

VI ≥ 10 mV, VO = 35 V

Positive Supply Current

I +

5.1

7.5

mA

IO = 0 A

Negative Supply Current

I -

4.1

5.0

mA

IO = 0 A

Input Offset Voltage Note6

VIO

±10

mV

V + - V - = 5 V to 30 V, RS ≤ 50 kΩ,

TA = 0 to +70

C

Input Offset Current Note6

IIO

±70

nA

V + - V - = 5 V to 30 V, TA = 0 to +70

C

Input Bias Current

IB

300

nA

V + - V - = 5 V to 30 V, TA = 0 to +70

C

Common Mode Input

Voltage Range

VICM

+13.0

-14.5

+13.8

-14.7

V

Output Saturation Voltage

VOL

0.23

0.4

V

V + ≥ 4.5 V, V - = 0 V, VI ≤ -10 mV,

IO = 8 mA

[Note] 6. The difference of the input voltage and the input bias current when the load current is 1 mA and the output is

inverted.