CS5501-AS datasheet(21/54 Pages) CIRRUS

21 / 54 page

+ or -) a clamp diode will be forward-biased. Un-

der these fault conditions the CS5501/CS5503

might be damaged. Under normal operating con-

ditions (with the power supplies established), the

device will survive transient currents through the

clamp diodes up to 100 mA and continuous cur-

rents up to 10 mA. The drive current into the AIN

pin should be limited to a safe value if an over-

voltage condition is likely to occur. See the

application note "Buffer Amplifiers for the

CS501X Series of A/D Converters" for further

discussion on the clamp diode input structure and

on current limiting circuits.

System Synchronization

If more than one CS5501/CS5503 is included in a

system which is operating from a common clock,

all of the devices can be synchronized to sample

and output at exactly the same time. This can be

accomplished in either of two ways. First, a single

CAL sig nal can be issued to all the

CS5501/CS5503’s in the system. To insure syn-

chronization on the same clock signal the CAL

signal should go low on the falling edge of

CLKIN. Or second, a common SLEEP control

signal can be issued. If the SLEEP signal goes

positive with the appropriate set up time to

CLKIN, all parts will be synchronized on the

same clock cycle.

Analog Input Impedance Considerations

The analog input of the CS5501/CS5503 can be

modeled as illustrated in Figure 11. A 20 pF ca-

pacitor is used to dynamically sample the input

signal. Every 64 CLKIN cycles the switch alter-

nately connects the capacitor to the output of the

buffer and then directly to the AIN pin. When-

ever the sample capacitor is switched from the

output of the buffer to the AIN pin, a small packet

of charge (a dynamic demand of current) will be

required from the input source to settle the volt-

age on the sample capacitor to its final value.

The voltage at the output of the buffer may differ

up to 100 mV from the actual input voltage due to

the offset voltage of the buffer. Timing allows 64

cycles of master clock (CLKIN) for the voltage

on the sample capacitor to settle to its final value.

The equation which defines settling time is:

= Vmaxe

−t

⁄RC

Where Ve is the final settled value, Vmax is the

maximum error voltage value of the input signal,

R is the value of the input source resistance, C is

the 20 pF sample capacitor plus the value of any

stray or additional capacitance at the input pin.

The value of t is equal to 64/CLKIN.

Vmax occurs the instance when the sample capaci-

tor is switched from the buffer output to the AIN

pin. Prior to the switch, AIN has an error esti-

mated as being less than or equal to Ve. Vmax is

equal to the prior error (Ve) plus the additional

error from the buffer offset. The estimate for

Vmax is:

Vmax

= Ve+100mV

20pF

(20pF+CEXT)

Where CEXT is the combination of any external

or stray capacitance.

From the equation which defines settling time, an

equation for the maximum acceptable source re-

sistance is derived

CS5501

AIN

AGND

100 mv

20 pF

CS5503

≤

Figure 11. Analog Input Model

CS5501/CS5503

DS31F2

CS5501-AS 数据表(PDF) 21 Page - Cirrus Logic

CS5501-AS 数据表(HTML) 21 Page - Cirrus Logic

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54

数据表下载