TOP242F datasheet(21/52 Pages) POWERINT

21 / 52 page

TOP242-250

1/02

Figure 41. 30 W Power Supply using External Current Limit Programming and Line Sensing for UV and OV.

Application Examples

A High Efficiency, 30 W, Universal Input Power Supply

The circuit shown in Figure 41 takes advantage of several of

the TOPSwitch-GX features to reduce system cost and power

supply size and to improve efficiency. This design delivers

30 W at 12 V, from an 85 to 265 VAC input, at an ambient of

°C, in an open frame configuration. A nominal efficiency

of 80% at full load is achieved using TOP244Y.

The current limit is externally set by resistors R1 and R2 to a

value just above the low line operating peak DRAIN current

of approximately 70% of the default current limit. This allows

use of a smaller transformer core size and/or higher transformer

primary inductance for a given output power, reducing

TOPSwitch-GX power dissipation, while at the same time

avoiding transformer core saturation during startup and output

transient conditions. The resistors R1 & R2 provide a signal

that reduces the current limit with increasing line voltage, which

in turn limits the maximum overload power at high input line

voltage. This function in combination with the built-in soft-

start feature of TOPSwitch-GX, allows the use of a low cost

RCD clamp (R3, C3 and D1) with a higher reflected voltage,

by safely limiting the TOPSwitch-GX drain voltage, with

adequate margin under worst case conditions. Resistor R4

provides line sensing, setting UV at 100 VDC and OV at

450 VDC. The extended maximum duty cycle feature of

TOPSwitch-GX (guaranteed minimum value of 75% vs. 64%

for TOPSwitch-II) allows the use of a smaller input capacitor

(C1). The extended maximum duty cycle and the higher

reflected voltage possible with the RCD clamp also permit the

use of a higher primary to secondary turns ratio for T1 which

reduces the peak reverse voltage experienced by the secondary

rectifier D8. As a result a 60 V Schottky rectifier can be used

for up to 15 V outputs, which greatly improves power supply

efficiency. The frequency reduction feature of the

TOPSwitch-GX eliminates the need for any dummy loading

for regulation at no load and reduces the no load/standby

consumption of the power supply. Frequency jitter provides

improved margin for conducted EMI meeting the CISPR 22

(FCC B) specification.

Output regulation is achieved by using a simple Zener sense

circuit for low cost. The output voltage is determined by the

Zener diode (VR2) voltage and the voltage drops across the

optocoupler (U2) LED and resistor R6. Resistor R8 provides

bias current to Zener VR2 for typical regulation of

±5% at the

12 V output level, over line and load and component

variations.

12 V

@ 2.5 A

1N4148

µF

10 V

LTV817A

VR2

1N5240C

10 V, 2%

150

Ω

R15

150

Ω

C14

1 nF

UF4005

68 k

Ω

2 W

4.7 nF

1 kV

CY1

2.2 nF

TOP244Y

150

Ω

µF

400 V

0.1

µF

MBR1060

C10

560

µF

35 V

C12

220

µF

35 V

C11

560

µF

35 V

RTN

6.8

Ω

4.7 M

Ω

1/2 W

2 M

Ω

1/2 W

9.09 k

Ω

PI-2657-040501

3.3

µH

BR1

600 V

3.15 A

20 mH

CX1

100 nF

250 VAC

CONTROL

TOPSwitch-GX

PERFORMANCE SUMMARY

Output Power:

30 W

Regulation:

± 4%

Efficiency:

≥ 79%

Ripple:

≤ 50 mV pk-pk

TOP242F 数据表(PDF) 21 Page - Power Integrations, Inc.

TOP242F 数据表(HTML) 21 Page - Power Integrations, Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

数据表下载

链接网址

TOP242F 数据表(PDF) 21 Page - Power Integrations, Inc.

TOP242F 数据表(HTML) 21 Page - Power Integrations, Inc.

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

数据表 下载

链接网址

数据表下载