SST25VF080B datasheet(14/33 Pages) MICROCHIP

14 / 33 page



2005-2020 Microchip Technology Inc.

DS20005045D-page 14

SST25VF080B

4.4.12

WRITE DISABLE (WRDI)

The Write Disable (WRDI) instruction resets the Write-

Enable-Latch bit and AAI bit to ‘0’ disabling any new

Write operations from occurring. The WRDI instruction

will not terminate any programming operation in prog-

ress. Any program operation in progress may continue

up to TBP after executing the WRDI instruction. CE#

must be driven high before the WRDI instruction is exe-

cuted.

FIGURE 4-16:

WRITE DISABLE (

WRDI)

SEQUENCE

4.4.13

ENABLE WRITE STATUS REGISTER

(EWSR)

The Enable Write STATUS Register (EWSR) instruction

arms the Write STATUS Register (WRSR) instruction

and opens the STATUS Register for alteration. The

Write STATUS Register instruction must be executed

immediately after the execution of the Enable Write

STATUS Register instruction. This two-step instruction

sequence of the EWSR instruction followed by the WRSR

instruction works like SDP (software data protection)

command structure which prevents any accidental

alteration of the STATUS Register values. CE# must be

driven low before the EWSR instruction is entered and

must be driven high before the EWSR instruction is exe-

cuted.

4.4.14

WRITE STATUS REGISTER (WRSR)

The Write STATUS Register instruction writes new val-

ues to the BP3, BP2, BP1, BP0, and BPL bits of the

STATUS Register. CE# must be driven low before the

command sequence of the WRSR instruction is entered

and driven high before the WRSR instruction is exe-

cuted. See Figure 4-17 for EWSR or WREN and WRSR

instruction sequences.

Executing the Write STATUS Register instruction will

be ignored when WP# is low and BPL bit is set to ‘1’.

When the WP# is low, the BPL bit can only be set from

‘0’ to ‘1’ to lock-down the STATUS Register, but cannot

be reset from ‘1’ to ‘0’. When WP# is high, the lock-

down function of the BPL bit is disabled and the BPL,

BP0, and BP1 and BP2 bits in the STATUS Register

can all be changed. As long as BPL bit is set to ‘0’ or

WP# pin is driven high (VIH) prior to the low-to-high

transition of the CE# pin at the end of the WRSR instruc-

tion, the bits in the STATUS Register can all be altered

by the WRSR instruction. In this case, a single WRSR

instruction can set the BPL bit to ‘1’ to lock down the

STATUS register as well as altering the BP0, BP1, and

BP2 bits at the same time. See Table 4-1 for a sum-

mary description of WP# and BPL functions.

FIGURE 4-17:

ENABLE WRITE STATUS REGISTER (

EWSR) OR WRITE ENABLE (WREN) AND

WRITE STATUS REGISTER (WRSR) SEQUENCE

CE#

SCK

0 1 234 5 6 7

MODE 0

MODE 3

High-Impedance

MODE 0

STATUS

7 65 4321 0

MODE 3

SCK

CE#

MODE 0

50 or 06

0 1 234 5 6 7

0 1 234 5 6 789 10 11 12 13 14 15

SST25VF080B 数据表(PDF) 14 Page - Microchip Technology

SST25VF080B 数据表(HTML) 14 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

数据表下载

链接网址

SST25VF080B 数据表(PDF) 14 Page - Microchip Technology

SST25VF080B 数据表(HTML) 14 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

数据表 下载

链接网址

数据表下载