IP82C55A datasheet(18/29 Pages) INTERSIL

18 / 29 page

FN2969.10

November 16, 2006

Absolute Maximum Ratings TA = +25°C

Thermal Information

Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +8.0V

Input, Output or I/O Voltage . . . . . . . . . . . . . GND-0.5V to VCC+0.5V

ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 1

Operating Conditions

Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +4.5V to 5.5V

Operating Temperature Range

CX82C55A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C

IX82C55A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to 85°C

MX82C55A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-55°C to 125°C

Die Characteristics

Gate Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000 Gates

Thermal Resistance (Typical, Note 1)

θJA (°C/W) θJC(°C/W)

CERDIP Package. . . . . . . . . . . . . . . . .

CLCC Package . . . . . . . . . . . . . . . . . .

PDIP Package . . . . . . . . . . . . . . . . . . .

N/A

PLCC Package. . . . . . . . . . . . . . . . . . .

N/A

MQFP Package . . . . . . . . . . . . . . . . . .

N/A

Maximum Storage Temperature Range . . . . . . . . . . -65°C to +150°C

Maximum Junction Temperature

CDIP Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +175°C

PDIP Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C

Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . +300°C

(PLCC and MQFP Lead Tips Only)

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

NOTE:

θJA is measured with the component mounted on an evaluation PC board in free air.

Electrical Specifications

VCC = 5.0V ±10%; TA = Operating Temperature Range

SYMBOL

PARAMETER

TEST CONDITIONS

MIN

MAX

UNITS

VIH

Logical One Input Voltage

2.0

2.2

-V

VIL

Logical Zero Input Voltage

-0.8

VOH

Logical One Output Voltage

IOH = -2.5mA,

IOH = -100μA

3.0

VCC -0.4

-V

VOL

Logical Zero Output Voltage

IOL +2.5mA

0.4

Input Leakage Current

VIN = VCC or GND, RD, CS, A1, A0, RESET, WR

-1.0

+1.0

μA

I/O Pin Leakage Current

VO = VCC or GND, D0 - D7

-10

+10

μA

IBHH

Bus Hold High Current

VO = 3.0V. Ports A, B, C

TA = -55°C

-50

-450

μA

TA = +128°C

-50

-400

μA

IBHL

Bus Hold Low Current

VO = 1.0V. Port A ONLY

TA = -55°C

450

μA

TA = +128°C

400

μA

IDAR

Darlington Drive Current

Ports A, B, C. Test Condition 3

-2.5

Note 2, 4

ICCSB

Standby Power Supply Current

VCC = 5.5V, VIN = VCC or GND. Output Open

μA

ICCOP

Operating Power Supply Current

TA = +25°C, VCC = 5.0V, Typical (See Note 3)

mA/MHz

NOTES:

2. No internal current limiting exists on Port Outputs. A resistor must be added externally to limit the current.

3. ICCOP = 1mA/MHz of Peripheral Read/Write cycle time. (Example: 1.0

μs I/O Read/Write cycle time = 1mA).

4. Tested as VOH at -2.5mA.

Capacitance TA = +25°C

SYMBOL

PARAMETER

TYPICAL

UNITS

TEST CONDITIONS

CIN

Input Capacitance

FREQ = 1MHz, All Measurements are referenced to

device GND

CI/O

I/O Capacitance

82C55A

IP82C55A 数据表(PDF) 18 Page - Intersil Corporation

IP82C55A 数据表(HTML) 18 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29

数据表下载