DN511
360.1 0 3.0 79.6 29 2.5 20.2
58 3.0
4.6
87 3.5
340.6 1 3.0 75.8 30 2.5 19.3
59 3.0
4.4
88 3.5
322.3 2 3.0 72.2 31 2.5 18.4
60 3.0
4.1
89 3.5
305.0 3 3.0 68.8 32 2.5 17.5
61 3.5
3.9
90 3.5
288.7 4 3.0 65.5 33 2.5 16.7
62 3.5
3.6
91 3.5
273.4 5 3.0 62.5 34 2.5 15.9
63 3.5
3.4
92 3.5
259.0 6 3.0 59.5 35 2.5 15.2
64 3.5
3.2
93 3.5
245.4 7 3.0 56.8 36 2.5 14.5
65 3.5
3.0
94 3.5
232.5 8 3.0 54.1 37 2.5 13.8
66 3.5
2.8
95 3.5
220.4 9 3.0 51.6 38 2.5 13.2
67 3.5
2.6
96 3.5
209.0 10 3.0 49.2 39 2.5 12.5
68 3.5
2.4
97 3.5
198.3 11 2.5 46.9 40 2.5 11.9
69 3.5
2.2
98 3.5
188.1 12 2.5 44.8 41 3.0 11.4
70 3.5
2.0
99 3.5
178.5 13 2.5 42.7 42 3.0 10.8
71 3.5
1.8 100 3.5
169.4 14 2.5 40.7 43 3.0 10.3
72 3.5
1.68 101 3.5
160.8 15 2.5 38.9 44 3.0
9.8
73 3.5. 1.52 102 3.5
152.7 16 2.5 37.1 45 3.5
9.3
74 3.5
1.37 103 3.5
145.1 17 2.5 35.4 46 3.0
8.9
75 3.5
1.23 104 3.5
137.8 18 2.5 33.8 47 3.0
8.4
76 3.5
1.09 105 3.5
131.0 19 2.5 33.8 47 3.0
8.0
77 3.5
0.95 106 3.5
124.5 20 2.5 30.8 49 3.0
7.6
78 3.5
0.82 107 3.5
118.3 21 2.5 29.4 50 3.0
7.2
79 3.5
0.70 108 3.5
112.5 22 2.5 28.1 51 3.0
6.8
80 3.5
0.58 109 3.5
107.0 23 2.5 26.8 52 3.0
6.5
81 3.5
0.46 110 3.5
101.8 24 2.5 25.5 53 3.0
6.1
82 3.5
0.35 111 3.5
96.9 25 2.5 24.4 54 3.0
5.8
83 3.5
0.25 112 3.5
92.2 26 2.5 23.2 55 3.0
5.5
84 3.5
0.14 113 3.5
87.8 27 2.5 22.2 56 3.0
5.2
85 3.5
0.04 114 3.5
83.6 28 2.5 21.2 57 3.0
4.9
86 3.5
RS
KΩ
T
°
C
TOL.
±°
C
RS
KΩ
T
°
C
TOL.
±°
C
RS
KΩ
T
°
C
TOL.
±°
C
RS
KΩ
T
°
C
TOL.
±°
C
0
10
20
30
40
50
60
70
20
40
60
80
100
120
POWER SUPPLY
VOLTAGE (VOLTS D.C.)
MAXIMUM HEATER TURN ON CURRENT
vs.
POWER SUPPLY VOLTAGE
This graph shows the range of D.C.
current that flows through the heater
before temperature control occurs.
3.0" ± 0.25"
0805 1% TEMPERATURE
SET RESISTOR ON
REQUEST
#32 GAGE MAGNET
WIRE (4 PLACES)
PIN 1
The temperature of the DN511 is supplied with
four 3 inch #32 gage magnet wire as shown
below. Temperature of the DN511 can be set at
the factory on request
140
0.00
0.50
1.00
1.50
2.00
2.50
3.00
3.50
4.00
0.0
20.0
40.0
60.0
80.0
SUPPLY VOLTAGE (VOLTS)
It is recommended that the DN511 heater be
attached to the device being heated with a
thermally conductive adhesive such as Loctite®
384. This will insure that there is minimum
thermal resistance between the two surfaces.
xxxx
DN505
Therm
Optics
xxxx
DN511
Therm
Optics
™
Page 2
Last Updated 6/25/01
1004 Mallory Way • Carson City, NV 89701 • Phone: 775-882-7721 • Fax: 775-882-7675 • E-mail: info@thermoptics.com • http://www.thermoptics.com
TYPICAL CASE TEMPERATURE
VS
CONTROL RESISTOR
TYPICAL HEATER POWER AT TURN ON
vs.
POWER SUPPLY VOLTAGE
Chinese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
