MAAPSS0076 datasheet(2/6 Pages) MACOM

2 / 6 page

DECT Power Amplifier

1880 - 1930 MHz

MAAPSS0076

M/A-COM Inc. and its affiliates reserve the right to make changes to the

product(s) or information contained herein without notice. M/A-COM makes

no warranty, representation or guarantee regarding the suitability of its

products for any particular purpose, nor does M/A-COM assume any liability

whatsoever arising out of the use or application of any product(s) or

information.

• North America Tel: 800.366.2266 / Fax: 978.366.2266

• Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300

• Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298

Visit www.macom.com for additional data sheets and product information.

RoHS

Compliant

Electrical Specifications: F = 1900 MHz, PIN = 0 dBm, VCC = 2.4 V, TA = 25 °C, Z0 = 50 Ω

Absolute Maximum Ratings 3,4

Parameter

Absolute Maximum

Input Power

+ 5 dBm

Operating Supply Voltage

+4.0 Volts

Operating Control Voltage

+3.0 Volts

Operating Temperature

-20 °C to +85 °C

Channel Temperature

+150 °C

Storage Temperature

-40 °C to +150 °C

Exceeding any one or combination of these limits may

cause permanent damage to this device.

M/A-COM does not recommend sustained operation near

these survivability limits.

Logic Table 5

VEN

State

OFF

LPM

HPM

5. 1 = +2.0 V to 2.5 V, 0 = 0 V to 0.5 V.

Operating the MAAPSS0076

The MAAPSS0076 is sensitive to electrostatic

discharge (ESD).

Use proper ESD control

techniques when handling this device. To operate

the MAAPSS0076, follow these steps. Ramp down

or shut down in reverse order.

1. Apply VCC (2.4 V).

2. Apply VM (0 or 2.5 V).

3. Apply PIN (-2 to 2 dBm).

4. Ramp VEN from 0 to 2.5 V.

Parameter

Test Conditions

Units

Min.

Typ.

Max.

Input Return Loss

VM = 0 V

VM = 2.5 V

—

POUT, High Power Mode (HPM)

VM = 2.5 V, VCC = 3.0 V

VCC = 2.4 V

VCC = 2.0 V

VCC = 1.8 V

dBm

—

26.5

25.5

24.0

23.5

—

POUT vs. Temperature, HPM

TA = 0 °C to 50 °C, VCC = 2.4 V

—

0.8

—

Current, HPM

VM = 2.5 V, VCC = 3.0 V

—

320

400

POUT, Low Power Mode (LPM)

VM = 0 V, VCC = 2.4 V

dBm

—

Current, LPM

VM = 0 V, VCC = 2.4 V

—

140

200

Current, Shutdown

VCC = 3.0 V, VEN = 0.5 V

µA

—

Control Pins

VEN, VM low

VEN, VM high

VM current

VEN current

2.0

—

0.5

2.5

1.0

3.0

Harmonics

VM = 2.5 V, VCC = 2.4 V

2fo

3fo

dBc

—

-50

-60

—

Forward Isolation

VEN = 0 V

Stability

+1.5 V < VCC < +3.5 V, POUT = HPM & LPM, VSWR < 6:1

-20

°C < TA < +70ºC, RBW = 3 MHz max. hold

Turn on/off time

ton: RF burst to (Avg Power – 1 dB)

toff: (Avg Power – 1 dB) to RF off

µS

—

All spurs < -60 dBc

POUT vs. VEN

VEN = 1.9 to 2.5 V

—

1.2

—

MAAPSS0076 数据表(PDF) 2 Page - Tyco Electronics

MAAPSS0076 数据表(HTML) 2 Page - Tyco Electronics

Html Pages

1 2 3 4 5 6

数据表下载