SPX1202M3 datasheet(2/12 Pages) SIPEX

2 / 12 page

Mar3-07

SPX202 600 mA Low Dropout Linear Regulator

at V

IN=VOUT + 1.5V, TA = 25C, CIN = COUT = 10F, unless otherwise specified. Limits in Boldface applies over the

full operating temperature range.

PARAMETER

CONDITIONS

TYP

MIN

MAX

UNITS

2.5V Version

Output Voltage

OUT= 10mA, V IN= 5.00V

2.475

2.500

2.525

0 ≤I

OUT ≤600mA, 4.50V ≤V IN ≤10V

2.450

2.550

3.0V Version

Output Voltage

OUT= 10mA, V IN= 5.00V

2.970

3.000

3.030

0 ≤I

OUT ≤600mA, 4.50V ≤V IN ≤10V

2.940

3.060

3.3V Version

Output Voltage

OUT= 10mA, V IN= 5.00V

3.267

3.300

3.333

0 ≤I

OUT ≤600mA, 4.50V ≤V IN ≤10V

3.234

3.366

All Output Options

Reference Voltage

OUT=10mA, (VIN - VOUT ) = 2V

1.238

1.250

1.262

10≤I

OUT≤600mA, 1.4V ≤(VIN-VOUT)≤10V

1.225

1.270

Output Voltage

(Note 1)

0.05

Temperature Stability

Line Regulation

4.50V≤V

IN≤12V,V OUT=3.00,IOUT=0

1.00

7.00

4.80V≤V

IN≤12V,V OUT=3.30,IOUT=0

1.00

7.00

6.50V≤V

IN≤12V,V OUT=5.00,IOUT=0

1.00

10.00

Load Regulation

0≤I

OUT≤600mA,V IN=4.50V,VOUT=3.00

1.00

12.00

0≤I

OUT≤600mA,V IN=4.80V,VOUT=3.30

1.00

12.00

0≤I

OUT≤600mA,V IN=6.50V,VOUT=5.0

1.00

15.00

Dropout Voltage

L =100mA

1.00

1.10

(Note 2)

L =600mA

1.05

1.15

Quiescent Current

4.25V≤V

IN≤6.5V

5.00

10.00

Adjust Pin Current

A

Current Limit

IN-VOUT)=5V

.850

1.0

Thermal Regulation

25C, 30mS Pulse

0.01

0.1

%/W

Ripple Rejection

RIPPLE=120Hz, (VIN-VOUT)=3V,

RIPPLE=1VPP

Long Term Stability

125C, 1000Hrs

0.03

RMS Output Noise

% of V

OUT, 10Hz≤f≤10kHz

0.003

Thermal Resistance

Junction to Case, at tab

C/W

ABSOLUTE MAXIMUM RATINGS

Power Dissipation ...................................... Internally Limited

Lead Temperature (soldering, 5 seconds) .................. 260C

Storage Temperature Range ...................... -65C to +150C

NOTES:

Note 1: Output temperature coefficient is defined as the worst case voltage change divided by the total temperature range.

Note 2: Dropout voltage is defined as the input to output differential at which the output voltage drops 100mV below its nominal value measured at 1V differential at

very low values of programmed output voltage, the minimum input supply voltage of 2V ( 2.3V over temperature) must be taken into account.

Note 3: Thermal regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied excluding load or line regulation effect.

Operating Junction Temperature Range ..... -40C to +125C

Input Supply Voltage ..................................................... +20V

ESD Rating .............................................................. 2kV min

ELECTRICAL CHARACTERISTICS

SPX1202M3 数据表(PDF) 2 Page - Sipex Corporation

SPX1202M3 数据表(HTML) 2 Page - Sipex Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

数据表下载

链接网址

SPX1202M3 数据表(PDF) 2 Page - Sipex Corporation

SPX1202M3 数据表(HTML) 2 Page - Sipex Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12

数据表 下载

链接网址

数据表下载