数据搜索系统,热门电子元器件搜索
  Chinese  ▼
ALLDATASHEETCN.COM

X  

M25PX32 数据表(PDF) 9 Page - STMicroelectronics

部件名 M25PX32
功能描述  32-Mbit, dual I/O, 4-Kbyte subsector erase, serial Flash memory with 75 MHz SPI bus interface
PDF  63 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
制造商  STMICROELECTRONICS [STMicroelectronics]
网页  http://www.st.com
标志 STMICROELECTRONICS - STMicroelectronics

M25PX32 数据表(HTML) 9 Page - STMicroelectronics

Back Button M25PX32 Datasheet HTML 5Page - STMicroelectronics M25PX32 Datasheet HTML 6Page - STMicroelectronics M25PX32 Datasheet HTML 7Page - STMicroelectronics M25PX32 Datasheet HTML 8Page - STMicroelectronics M25PX32 Datasheet HTML 9Page - STMicroelectronics M25PX32 Datasheet HTML 10Page - STMicroelectronics M25PX32 Datasheet HTML 11Page - STMicroelectronics M25PX32 Datasheet HTML 12Page - STMicroelectronics M25PX32 Datasheet HTML 13Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 9 / 63 page
background image
M25PX32
Signal descriptions
9/63
2
Signal descriptions
2.1
Serial Data output (DQ1)
This output signal is used to transfer data serially out of the device. Data are shifted out on
the falling edge of Serial Clock (C).
During the Dual Input Fast Program (DIFP) instruction, pin DQ1 is used as an input. It is
latched on the rising edge of the Serial Clock (C).
2.2
Serial Data input (DQ0)
This input signal is used to transfer data serially into the device. It receives instructions,
addresses, and the data to be programmed. Values are latched on the rising edge of Serial
Clock (C).
During the Dual Output Fast Read (DOFR) instruction, pin DQ0 is used as an output. Data
are shifted out on the falling edge of the Serial Clock (C).
2.3
Serial Clock (C)
This input signal provides the timing of the serial interface. Instructions, addresses, or data
present at Serial Data input (DQ0) are latched on the rising edge of Serial Clock (C). Data
on Serial Data output (DQ1) changes after the falling edge of Serial Clock (C).
2.4
Chip Select (S)
When this input signal is High, the device is deselected and Serial Data output (DQ1) is at
high impedance. Unless an internal Program, Erase or Write Status Register cycle is in
progress, the device will be in the Standby Power mode (this is not the Deep Power-down
mode). Driving Chip Select (S) Low enables the device, placing it in the Active Power mode.
After Power-up, a falling edge on Chip Select (S) is required prior to the start of any
instruction.
2.5
Hold (HOLD)
The Hold (HOLD) signal is used to pause any serial communications with the device without
deselecting the device.
During the Hold condition, the Serial Data output (DQ1) is high impedance, and Serial Data
input (DQ0) and Serial Clock (C) are Don’t care.
To start the Hold condition, the device must be selected, with Chip Select (S) driven Low.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63


数据表 下载

Go To PDF Page


链接网址



ALLDATASHEET是否为您带来帮助?  [ DONATE ] 

关于 Alldatasheet   |   广告服务   |   联系我们   |   隐私政策   |   数据表链接    |   链接交换   |   制造商名单
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com