24LC512-ISLASHMC datasheet(9/42 Pages) MICROCHIP

9 / 42 page

DS21930B-page 9

24AAXX/24LCXX/24FCXX

3.0

PIN DESCRIPTIONS

The descriptions of the pins are listed in Table 3-1.

TABLE 3-1:

PIN FUNCTION TABLE

3.1

A0, A1, A2 Chip Address Inputs

The A0, A1 and A2 pins are not used by the 24XX01

through 24XX16 devices.

The A0, A1 and A2 inputs are used by the 24C01C,

24C02C, 24XX014, 24XX024, 24XX025 and the

24XX32 through 24XX512 for multiple device opera-

tions. The levels on these inputs are compared with the

corresponding bits in the slave address. The chip is

selected if the compare is true.

For the 24XX128 and 24XX256 in the MSOP package

only, pins A0 and A1 are not connected.

Up to eight devices (two for the 24XX128 and

24XX256 MSOP package) may be connected to the

same bus by using different Chip Select bit

combinations.

In most applications, the chip address inputs A0, A1

and A2 are hard-wired to logic ‘0’ or logic ‘1’. For

applications in which these pins are controlled by a

microcontroller or other programmable device, the chip

address pins must be driven to logic ‘0’ or logic ‘1’

before normal device operation can proceed.

3.2

Serial Data (SDA)

This is a bidirectional pin used to transfer addresses

and data into and out of the device. It is an open drain

terminal. Therefore, the SDA bus requires a pull-up

resistor to VCC (typical 10 k

Ω for 100 kHz, 2 kΩ for

400kHz and 1MHz).

For normal data transfer, SDA is allowed to change

only during SCL low. Changes during SCL high are

reserved for indicating the Start and Stop conditions.

3.3

Serial Clock (SCL)

This input is used to synchronize the data transfer to

and from the device.

3.4

Write-Protect (WP)

This pin must be connected to either VSS or VCC. If tied

to VSS, write operations are enabled. If tied to VCC,

write operations are inhibited but read operations are

not affected. See Table 1-1 for the write-protect

scheme of each device.

3.5

Power Supply (VCC)

A VCC threshold detect circuit is employed which

disables the internal erase/write logic if VCC is below

1.5V at nominal conditions. For the 24C00, 24C01C

and 24C02C devices, the erase/write logic is disabled

below 3.8V at nominal conditions.

Name

8-Pin

PDIP and

SOIC

8-Pin

TSSOP and

MSOP

5-Pin SOT-23

24XX00

5-Pin SOT-23

All except

24XX00

14-Pin

TSSOP

8-Pin

5x6 DFN and

2x3 DFN

Function

1(1)

—

User configurable Chip Select(3)

2(1)

——

User configurable Chip Select(3)

—

User configurable Chip Select(3)

VSS

Ground

SDA

Serial Data

SCL

Serial Clock

(NC)

—

3, 4, 5,

10, 11, 12

—

Not Connected

7(2)

—

Write-Protect Input

VCC

Power Supply

Note 1:

Pins 1 and 2 are not connected for the 24XX128 and 24XX256 MSOP packages.

Pin 7 is not used for 24XX00, 24XX025 and 24C01C.

Pins A0, A1 and A2 are not used by some devices (no internal connections). See Table 1-1 for details.

24LC512-I/MC 数据表(PDF) 9 Page - Microchip Technology

24LC512-I/MC 数据表(HTML) 9 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

数据表下载

链接网址

24LC512-I/MC 数据表(PDF) 9 Page - Microchip Technology

24LC512-I/MC 数据表(HTML) 9 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

数据表 下载

链接网址

数据表下载