Data Sheet

AD8376

Rev. B | Page 21 of 24

Table 6. Evaluation Board Configuration Options

Components

Function

Default Conditions

C13, C14, C20 to C22,

C64 to C67, R90, R91

Power Supply Decoupling. Nominal supply decoupling consists a

10 µF capacitor to ground followed by 0.1 µF capacitors to ground

positioned as close to the device as possible.

C20 = 10 µF (size 3528)

C13, C14 = 0.1 µF (size 0402)

C21, C22, C64 to C67 = 0.1 µF

(size 0603)

R90, R91 = 0 Ω (size 0603)

T1, T2, C1 to C4, C61, C62,

R1 to R4, R9 to R12,

R70 to R75

Input Interface. T1 and T2 are 3:1 impedance ratio baluns to

transform a 50 Ω single-ended input into a 150 Ω balanced

differential signal. R1 and R4 ground one side of the differential drive

interface for single-ended applications. R9 to R12 and R70 to R75 are

provided for generic placement of matching components. C1 to C4

are dc blocks.

T1, T2 = TC3-1+ (Mini-Circuits)

C1 to C4, C60, C61 = 0.1 µF (size 0402)

R1, R4, R9 to R12 = 0 Ω (size 0402)

R2, R3, R70 to R75 = open (size 0402)

T3, T4, C7 to C10,

L1 to L4, R15 to R32,

R62, R63, C62, C63

Output Interface. C7 to C10 are dc blocks. L1 to L4 provide dc biases

for the outputs. R19 to R28 are provided for generic placement of

matching components. The evaluation board is configured to

provide a 150 Ω to 50 Ω impedance transformation with an insertion

loss of about 11 dB. T3 and T4 are 1:1 impedance ratio baluns to

transform the balanced differential signals to single-ended signals.

R29 and R32 ground one side of the differential output interface for

single-ended applications.

C7 to C10 = 0.1 µF (size 0402)

L1 to L4 = 1 µH (size 0805)

T3, T4 = ETC1-1-13 (M/A-COM)

R19 to R22 = 61.9 Ω (size 0402)

R23, R25, R26, R28 = 30.9 Ω (size 0402)

R15 to R18 = 0 Ω (size 0603)

R29, R32 = 0 Ω (size 0402)

R24, R27, R30, R31, R62, R63 = open

(size 0402)

C62, C63 = 0.1 µF (size 0402)

PUA, PUB, R13, R14,

C5, C6

Enable Interface. The AD8376 is enabled by applying a logic high

voltage to the ENBA pin for Channel A or the ENBB pin for Channel B.

Channel A is enabled when the PUA switch is set in the up position,

connecting the ENBA pin to VPOS. Likewise, Channel B is enabled

when the PUB switch is set in the up position, connecting the ENBB

pin to VPOS. Both channels are disabled by setting the switches to

the down position, connecting the ENBA and ENBB pins to GND.

PUA, PUB = installed

R13, R14 = 0 Ω (size 0603)

C5, C6 = open (size 0603)

WA0 to WA4, WB0 to WB4

Parallel Interface Control. Used to hardwire A0 through A4 and B0

through B4 to the desired gain. The bank of switches WA0 to WA4 set

the binary gain code for Channel A. The bank of switches WB0 to

WB4 set the binary gain code for Channel B. WA0 and WB0 represent

the LSB for each of the respective channels.

WA0 to WA4, WB0 to WB4 = installed

C11, C12

Voltage Reference. Input common-mode voltage ac-coupled to

ground by 0.1 µF capacitors, C11 and C12.

C11, C12 = 0.1 µF (size 0402)