PI2DBS412 datasheet(2/9 Pages) PERICOM

2 / 9 page

PS8786C

0505/07

PI2DBS412

1.8V, 1.8GHz, Differential Broadband Signal Switch,

4-Differential Channel, 2:1 Mux/DeMux Switch

Storage Temperature....................................–65°C to +150°C

Supply Voltage to Ground Potential...............–0.5V to +2.5V

DC Input Voltage ............................................–0.5V to VCC

DC Output Current......................................................120mA

Power Dissipation...........................................................0.5W

Note:

Stresses greater than those listed under MAXIMUM RATINGS may cause

permanent damage to the device. This is a stress rating only and func-

tional operation of the device at these or any other conditions above those

indicated in the operational sections of this speciﬁcation is not implied.

Exposure to absolute maximum rating conditions for extended periods

may affect reliability.

Maximum Ratings

(Above which useful life may be impaired. For user guidelines, not tested.)

DC Electrical Characteristics for Switching over Operating Range (TA = –40°C to +85°C, VCC = 1.5V to 2.0V)

Paramenter

Description

Test Conditions(1)

Min.

Typ.(2)

Max.

Units

VIH

Input HIGH Voltage

Guaranteed HIGH level

0.65 x VCC

VIL

Input LOW Voltage

Guaranteed LOW level

–0.5

0.35 x VCC

VIK

Clamp Diode Voltage

VCC = Max., IIN = –18mA

–0.7

–1.2

IIH

Input HIGH Current

VCC = Max., VIN = VCC

±5

μA

IIL

Input LOW Current

VCC = Max., VIN = GND

±5

Dynamic Electrical Characteristics Over the Operating Range (TA= –40º to +85ºC, VCC = 1.8V±10%, GND=0V)

Parameter

Description

Test Conditions(1)

Min.

Typ.(2)

Max.

Units

XTALK(3)

Crosstalk

See Fig. 1 for Measurement Setup, f = 10 MHz

–68

OIRR(3)

OFF Isolation

See Fig. 2 for Measurement Setup, f = 10 MHz

–77

BW(3)

Bandwidth

1.8

GHz

Notes:

For Max. or Min. conditions, use appropriate value speciﬁed under Electrical Characteristics for the applicable device type.

Typical values are at VCC = 1.8V, TA = 25°C ambient and maximum loading.

Guaranteed by design.

Power Supply Characteristics

Parameters

Description

Test Conditions(1)

Min.

Typ.(2)

Max.

Units

ICC

Quiescent Power Supply Current

VCC = Max., VIN = GND or VCC

200

μA

Notes:

For Max. or Min. conditions, use appropriate value speciﬁed under Electrical Characteristics for the applicable device type.

Typical values are at VCC = 1.8V, TA = 25°C ambient and maximum loading.

Notes:

For Max. or Min. conditions, use appropriate value speciﬁed under Electrical Characteristics for the applicable device type.

Typical values are at VCC = 1.8V, TA = 25°C ambient and maximum loading.

07-0123

PI2DBS412 数据表(PDF) 2 Page - Pericom Semiconductor Corporation

PI2DBS412 数据表(HTML) 2 Page - Pericom Semiconductor Corporation

Html Pages

1 2 3 4 5 6 7 8 9

数据表下载

链接网址

PI2DBS412 数据表(PDF) 2 Page - Pericom Semiconductor Corporation

PI2DBS412 数据表(HTML) 2 Page - Pericom Semiconductor Corporation

Html Pages

1 2 3 4 5 6 7 8 9

数据表 下载

链接网址

数据表下载