PI3USB102ZLE datasheet(2/7 Pages) PERICOM

2 / 7 page

PI3USB102

USB 2.0 High-Speed (480 Mbps) Signal Switch

Targeted for Battery Powered Applications

P-0.6

03/27/07

DC Electrical Characteristics for USB 2.0 Switching over Operating Range

(TA = –40°C to +85°C, VCC = 3.0 - 4.4V)

Paramenter

Description

Test Conditions(1)

Min.

Typ.(2)

Max.

Units

VIH

Input HIGH Voltage

Guaranteed

HIGH level

VCC = 4.2V

1.8

VCC = 3.3V

1.6

VIL

Input LOW Voltage

Guaranteed HIGH level

0.8

VIK

Clamp Diode Voltage

VCC = Max., IIK = –18mA

-1.2

IIH

Input HIGH Current

VCC = Max., VIH = VCC

±5

IIL

Input LOW Current

VCC = Max., VIL = GND

±5

RON

Switch On-Resistance(3)

VCC = Min., -0.4V ≤ Vinput ≤ 1.0V,

ION = –40mA

5.5

6.0

RFLAT(ON)

On-Resistance Flatness(3)

VCC = Min., -0.4V ≤ Vinput ≤ 1.0V,

ION = -40mA

1.5

RON

On-Resistance match from cen-

ter ports to any other port(3)

VCC = Min., -0.4V ≤ Vinput ≤ 1.0V,

ION = -40mA

0.9

2.0

Notes:

For max. or min. conditions, use appropriate value speciﬁed under Electrical Characteristics for the applicable device type.

VCC = 3.0 - 4.4V, TA = 25°C ambient and maximum loading.

Measured by the voltage drop between D and Dn pin at indicated current through the Switch On-Resistance is determined by the lower of the

voltages on the two (D, Dn) pins.

Storage Temperature ......................................................–65°C to +150°C

Supply Voltage to Ground Potential .................................–0.5V to +4.6V

DC Input Voltage ..................................................... –0.5V to VCC +0.5V

DC Output Current ........................................................................120mA

Power Dissipation .............................................................................0.5W

Note: Stresses greater than those listed under MAXIMUM

RATINGS may cause permanent damage to the device. This

is a stress rating only and functional operation of the device

at these or any other conditions above those indicated in the

operational sections of this speciﬁcation is not implied. Ex-

posure to absolute maximum rating conditions for extended

periods may affect reliability.

Maximum Ratings

(Above which useful life may be impaired. For user guidelines, not tested.)

Power Supply Characteristics (VCC = 3.0 - 4.4V)

Parameters

Description

Test Conditions(1)

Min.

Typ.

Max.

Units

ICC

Quiescent Power Supply Current

VCC = Max., VSEL = GND or VCC

Notes:

For max. or min. conditions, use appropriate value speciﬁed under Electrical Characteristics for the applicable device type.

07-0095

PI3USB102ZLE 数据表(PDF) 2 Page - Pericom Semiconductor Corporation

PI3USB102ZLE 数据表(HTML) 2 Page - Pericom Semiconductor Corporation

Html Pages

1 2 3 4 5 6 7

数据表下载

链接网址

PI3USB102ZLE 数据表(PDF) 2 Page - Pericom Semiconductor Corporation

PI3USB102ZLE 数据表(HTML) 2 Page - Pericom Semiconductor Corporation

Html Pages

1 2 3 4 5 6 7

数据表 下载

链接网址

数据表下载