MAAPSS0113 datasheet(2/7 Pages) MACOM

2 / 7 page

• North America Tel: 800.366.2266 / Fax: 978.366.2266

• Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300

• Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298

Visit www.macom.com for additional data sheets and product information.

M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s) or

information contained herein without notice.

DECT Power Amplifier

1880 - 1930 MHz

M/A-COM Products

Rev. V1

MAAPSS0113

ADVANCED: Data Sheets contain information regarding a product M/A-COM is considering for

development. Performance is based on target specifications, simulated results, and/or prototype

measurements. Commitment to develop is not guaranteed.

PRELIMINARY: Data Sheets contain information regarding a product M/A-COM has under develop-

ment. Performance is based on engineering tests. Specifications are typical. Mechanical outline has

been fixed. Engineering samples and/or test data may be available. Commitment to produce in

volume is not guaranteed.

Parameter

Test Conditions

Units

Min.

Typ.

Max.

Input Power

dBm

—

Input Return Loss

VM = 0 V

VM = 1.7 V

—

POUT, High Power Mode (HPM)

VM = 1.7 V, VCC = 3.0 V

VCC = 2.4 V

VCC = 2.0 V

VCC = 1.8 V

dBm

—

25.5

23.5

—

POUT vs. Temperature, HPM

TA = 0 °C to 50 °C, VCC = 2.4 V

—

0.8

—

POUT vs. VEN

VEN = 1.6 t o 1.9 V , VCC = 2.4 V

—

Current, HPM

VM = 1.7 V, VCC = 3.0 V

—

350

500

POUT, Low Power Mode (LPM)

VM = 0 V, VCC = 2.4 V

dBm

—

Current, LPM

VM = 0 V, VCC = 2.4 V

—

150

Current, Shutdown

VCC = 3.0 V, VEN = 0.5 V

µA

—

Control Pins

VEN, VM low

VEN, VM high

VM current

VEN current

1.6

—

1.7

0.5

1.9

Harmonics

VM = 1.7 V, VCC = 2.4 V

2fo

3fo

dBc

—

-33

-35

—

Forward Isolation

VEN = 0 V, VCC = 2.4 V

—

Stability

+1.5 V < VCC < +3.5 V, POUT = HPM & LPM, VSWR < 6:1

-20

°C < TA < +70ºC

Turn on/off time

ton: RF burst to (Avg Power – 1 dB)

toff: (Avg Power – 1 dB) to RF off

µS

—

All spurs < -60 dBc

Electrical Specifications: F = 1880 - 1930 MHz, TA = 25 °C, Z0 = 50 Ω

Absolute Maximum Ratings 4,5,6

Parameter

Absolute Maximum

Input Power

5 dBm

Operating Supply Voltage

4.0 Volts

Operating Control Voltage

3.0 Volts

Operating Temperature

-20 °C to +85 °C

Channel Temperature

150 °C

Storage Temperature

-40 °C to +150 °C

4. Exceeding any one or combination of these limits may cause

permanent damage to this device.

5. M/A-COM does not recommend sustained operation near

these survivability limits.

6. For operation above 4V as required for 3 cell systems, a drop-

ping diode is required. See application note page 6.

Logic Table 7

VEN

State

OFF

LPM

HPM

7. Logic 1 = 1.6 V to 1.9 V, Logic 0 = 0 V to 0.5 V.

Operating the MAAPSS0113

The MAAPSS0113 is sensitive to electrostatic

discharge (ESD).

Use proper ESD control

techniques when handling this device. To operate

the MAAPSS0113, follow these steps. Ramp down

or shut down in reverse order.

1. Apply VCC (2.4 V).

2. Apply VM (0 or 1.7 V).

3. Apply PIN (-2 to 2 dBm).

4. Ramp VEN from 0 to 1.7 V.

MAAPSS0113 数据表(PDF) 2 Page - Tyco Electronics

MAAPSS0113 数据表(HTML) 2 Page - Tyco Electronics

Html Pages

1 2 3 4 5 6 7

数据表下载