| 数据搜索系统,热门电子元器件搜索 |
|
RT9243GS 数据表(PDF) 3 Page - Richtek Technology Corporation |
|
|
|||||||||||||||||||||||||||||
RT9243GS 数据表(HTML) 3 Page - Richtek Technology Corporation |
|
3 / 18 page ![]() RT9243 3 DS9243-07 March 2007 www.richtek.com Functional Pin Description OVP (Pin 1) Over voltage trip output. PGOOD (Pin 2) Power good open-drain output. VID4 (Pin 3), VID3 (Pin 4), VID2 (Pin 5), VID1 (Pin 6), VID0 (Pin 7) & VID125 (Pin 8) DAC voltage identification inputs for VRD10.x. These pins are internally pulled to 3V if left open. VOSS (Pin 9) VCORE initial value offset. Connect this pin to GND with a resistor to set the offset value. ADJ (Pin 10) Current sense output for active droop adjust. Connect a resistor from this pin to GND to set the load droop. SS (Pin 11) Connect this SS pin to GND with a capacitor to set the soft-start time interval. Pulling this pin below 1V (ramp valley of sawtooth wave in pulse width modulator) would make all PWMs low, turn on low side MOSFETs and turn off high side MOSFETs. FB (Pin 12) Inverting input of the internal error amplifier. COMP (Pin 13) Output of the error amplifier and input of the PWM comparator. VDIF (Pin 14) VCORE differential sense output. VSEN (Pin 19) VCORE differential sense positive input. SGND (Pin 20) VCORE differential sense negative input. GND (Pin 21) Ground for the IC. PWM1 (Pin 25), PWM2 (Pin 26), PWM3 (Pin 22) & PWM4 (Pin 29) PWM outputs for each driven channel. Connect these pins to the PWM input of the MOSFET driver. For systems which use 3 channels, connect PWM4 high. Two channel systems connect PWM3 and PWM4 high. ISN1 (Pin 18), ISN2 (Pin 17), ISN3 (Pin 16) & ISN4 (Pin 15) RDS(ON) current sense inputs from each individual converter channel sense component's GND node. ISP1 (Pin 24), ISP2 (Pin 27), ISP3 (Pin 23) & ISP4 (Pin 28) RDS(ON) current sense inputs for each individual converter channel. Tie this pin to the component's sense node. VCC (Pin 30) IC power supply. Connect this pin to a 5V supply. DVD (Pin 31) Programmable power UVLO detection input. Trip threshold = 2V at VDVD rising. RT (Pin 32) Switching frequency setting. Connect this pin to GND with a resistor to set the frequency. (k Ω) Frequency vs. RRT 0 50 100 150 200 250 300 350 400 450 0 10 20304050 6070 RRT |
|
|
链接网址 |
| ALLDATASHEET是否为您带来帮助? [ DONATE ] |
关于 Alldatasheet | 广告服务 | 联系我们 | 隐私政策 | 数据表链接 | 链接交换 | 制造商名单 All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |