ABSOLUTE MAXIMUM RATINGS

Supply Voltage V

DD

-0.5 V to 7.0 V

Storage Temperature

-55

Maximum Process Temperature 260

STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com

YS

TEM

CERTIFIC

AT

01

10106 Rev F

SPECIFICATIONS

Specifications are typical at 25

Specifications are subject to change without notice. Tighter

specifications available. Please contact factory.

Supply Voltage

1

300 kHz to 120 MHz

2

5.0 V

10%

300 kHz to 170 MHz

2

3.3 V

10%

Calibration Tolerance

3

100 ppm

Frequency Stability

50 ppm for Commercial

Over Temperature

4

100 ppm for Industrial

100 ppm for Military

Supply Current

3.3 V

5.0 V

(Typical)

10 MHz

2 mA

4 mA

24 MHz

4 mA

8 mA

30 MHz

6 mA

10 mA

40 MHz

8 mA

12 mA

50 MHz

10 mA

14 mA

CMOS

5

15 pF

Start-up Time

5 ms MAX

Rise/Fall Time

6 ns MAX

Duty Cycle

40% MIN, 60% MAX

Aging, first year

10 ppm MAX

Shock, survival

6

Vibration, survival

7

20 g , 10-2000 Hz swept sine

Operating Temp. Range -10

-40

-55

1. Other voltages available. Contact factory.

2. Not all frequencies available at all voltage/enable combinations.

3. Other tolerances available.

4. Does not include calibration tolerance. Other tolerances available.

5. Higher CMOS loads and TTL loads available. Contact factory.

6. Higher shock version available. Contact factory about CXOHG.

7. Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also

available.

Note: All parameters are measured at ambient temperature with a 10M

Ω,15 pF load.

PACKAGING OPTIONS

CXO

- Tray Pack

- 16 mm tape, 7˝ or 13˝ reels

+

_

+

_

+

_

+

_

+

_

+

_

HOW TO ORDER CXO SURFACE MOUNT CRYSTAL OSCILLATORS

“S” if special,

custom design,

or if the voltage

is not 5.0 V.

Otherwise,

leave blank.

CXO

S

T

SM3

32.0M ,

Frequency

K = kHz

M = MHz

Enable/Disable Option

E, T or N

Terminations

Blank = SM1

= Gold Plated

SM3 = Solder Dipped

SM5 = Solder Dipped

Lead Free

100

/

100

/

/

I

//

200

/

I

Temp. Range:

C= -10

I

= -40

M= -55

S= Customer Specified

Total

Frequency

Tolerance

(in ppm)

Temp. Range:

C= -10

I

= -40

M= -55

S= Customer Specified

Frequency

Stability over

Temp.Range

(in ppm)

Calibration

Tolerance

@ 25

(in ppm)

OR

Pb

ET

When enabled (PIN 1 is high*)

Output

Freq. output

Freq. output

Oscillator

Oscillates

Oscillates

Current consumption

Normal

Normal

When disabled (PIN 1 is low)

Output

High Z state

High Z state

Oscillator

Stops

Oscillates

Current consumption

Very low

Lower than normal

When re-enabled (PIN 1 changes from low to high)

Output recovery

Delayed

Immediate

ENABLE/DISABLE OPTIONS (E/T/N)

Statek offers three enable/disable options: E, T, and N.

Both the E-version and T-version have Tri-State outputs

and differ in whether the oscillator continues to run

internally when the output is put into the high Z state: it

stops in the E-version and continues to run in the

T-version. So, the E-version offers very low current

consumption when the oscillator is disabled and the

T-version offers very fast output recovery when the

oscillator is re-enabled. The N-version does not have

PIN 1 connected internally and so has no enable/disable

capability.

The following table summarizes the three

options.

COMPARISON OF

ENABLE/DISABLE OPTIONS E AND T