CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

CF

series

Chip Type, Standard

Specifications

Characteristics of Temperature

Impedance Ratio

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

tan

δ

ESR (1)

Leakage Current (

2)

Performance Characteristics

Item

– 55 ~ +105°C

2.5 ~ 25V

6.8 ~ 1500µF

± 20% at 120Hz, 20°C

Not more than value of Standard ratings at 120Hz, 20°C

Not more than value of Standard ratings at 100kHz, 20°C

Not more than value of Standard ratings.

After 2 minute's application of rated voltage.

20°C

Z+105°C / Z+20°C

1.25

(100kHz)

Z

– 55°C / Z+20°C

1.25

Endurance

Damp Heat

Resistance to

Soldering Heat

Marking

After 2000 hours' application of rated voltage

at 105°C, capacitors meet the specified value

for life characteristics listed at right.

After 1000 hours' application of rated voltage

at 60°C 90%RH, capacitors meet the specified value

for life characteristics listed at right.

To comply with recommended conditions for

reflow soldering. Pre-heating shall be done

at 150 ~ 200°C and for 60 ~ 180 sec.

In the case of peak temp, less than 250°C,

reflow soldering shall be within two times.

In the case of peak temp, less than 260°C,

reflow soldering shall be once.

Measurement for solder temperature profile shall

be made at the capacitor top and the terminal.

Navy blue print on the case top

Capacitance change

tan

δ

Leakage current (

2)

Within ± 20% of initial value (

3)

150% or less of the initial specified value

150% or less of the initial specified value

Initial specified value or less

Capacitance change

tan

δ

Leakage current (

2)

Within ± 20% of initial value (

3)

150% or less of the initial specified value

150% or less of the initial specified value

Initial specified value or less

Capacitance change

tan

δ

Leakage current (

2)

Within ± 10% of initial value (

3)

130% or less of the initial specified value

130% or less of the initial specified value

Initial specified value or less

Ultra Low ESR, High ripple current.

Load life of 2000 hours at 105°C.

SMD type : Lead free reflow soldering condition at 260°C peak

correspondence.

Adapted to the RoHS directive (2002/95/EC).

1 ESR measurements should be made at a point on the terminal nearest where the terminals protrude through the plastic platform.

2 Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the

temperature of 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

H

0.3 MAX.

C±0.2

L

Series

Voltage ( j:6.3v)

Plastic platform

Lot No.

Capacitance

Negative

Positive

+0.1

-0.4

Dimensions

Type numbering system (Example : 6.3V 150µF)

Voltage

V

2.5

4

6.3

10

16

20

25

Code

e

g

j

A

C

D

E

Size

φD

L

A

B

C

E

H

φ6.3

6.3

5.9

7.3

6.6

6.6

2.1

0.5 ~ 0.8

φ8

8.0

6.9

9.0

8.3

8.3

3.2

0.8 ~ 1.1

φ10

10.0

7.9

11.0

10.3

10.3

4.6

0.8 ~ 1.1

φ10

10.0

9.9

11.0

10.3

10.3

4.6

0.8 ~ 1.1

(mm)

Dimension table in next page.

CAT.8100V