ALUMINUM ELECTROLYTIC CAPACITORS

Series

Series

Voltage (C:16V)

Capacitance

(f4 ~ 6.3 )

(f8 ´ 6.2 )

Plastic platform

0.3 MAX.

L

(L±0.3)

+0.1

Ð0.2

C±0.2

H

H

Positive

Negative

Trade mark

Lot No.

Plastic platform

0.3 MAX.

L±0.3

1 Apply to f6.3 ´ 5.8, f6.3 ´ 7.7

C±0.2

Positive

Negative

Voltage ( A:10V)

Capacitance

Lot No.

Series

(f8 ´ 10, f10´10)

H

Trade mark

Plastic platform

0.3 MAX.

L±0.5

C±0.2

Positive

Negative

Voltage (V:35V)

Capacitance

Lot No.

1

fD

4 ~ 6.3 (5.4L)

6.3 ~ 10 (L 5.8L)

code

GB

GS

A

B

C

E

L

H

4 ´ 5.4

1.8

4.3

4.3

1.0

5.4

0.5 ~ 0.8

5 ´ 5.4

2.1

5.3

5.3

1.3

5.4

0.5 ~ 0.8

6.3 ´ 5.4

2.4

6.6

6.6

2.2

5.4

0.5 ~ 0.8

6.3 ´ 5.8

2.4

6.6

6.6

2.2

5.4

0.5 ~ 0.8

6.3 ´ 7.7

2.4

6.6

6.6

2.2

7.7

0.5 ~ 0.8

8 ´ 6.2

3.3

8.3

8.3

2.3

6.2

0.5 ~ 0.8

8 ´ 10

2.9

8.3

8.3

3.1

10

0.8 ~ 1.1

10 ´ 10

3.2

10.3

10.3

4.5

10

0.8 ~ 1.1

fD

(mm)

U

1

W

2

Z

3

0

4

J

5

3

6

3

7

0

8

M

9

C

10

L

11

1

12

G

13

B

14

Configuration

Package code

Capacitance tolerance (±20%)

Rated Capacitance (33mF)

Rated voltage (6.3V)

Series name

Type

WZ

series

Recomended reflow condition : 260°C peak 5 sec 230°C over 60 sec 2 times

(

φ8 × 6.2, φ10 × 10 : 1 time)

Applicable to automatic mounting machine using carrier tape.

Adapted to the RoHS directive (2002/95/EC).

Chip Type

Specifications

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Leakage Current

tan

δ

Stability at Low Temperature

Endurance

Shelf Life

Marking

Performance Characteristics

Item

– 55 ~ +105°C

6.3 ~ 50V

0.1 ~ 1500µF

±20% at 120Hz, 20°C

After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater.

Black print on the case top.

Measurement frequency : 120Hz, Temperature : 20°C

Measurement frequency : 120Hz

After 1000 hours' application of rated voltage

at 105°C, capacitors meet the characteristic

requirements listed at right.

After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4

clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.

Resistance to soldering

heat

The capacitors shall be kept on the hot plate maintained at 250°C

for 30 seconds. After removing from the hot plate and restored

at room temperature, they meet the characteristic requirements

listed at right.

Rated voltage (V)

tan

δ (MAX.)

6.3

0.30

10

0.24

16

0.20

25

0.16

35

0.14

50

0.14

Z– 25°C / Z+20°C

Z– 40°C / Z+20°C

Rated voltage (V)

Impedance ratio

ZT / Z20 (MAX.)

6.3

4

8

10

3

8

16

2

4

25

2

4

35

2

3

50

2

3

Capacitance

change

Leakage current

tan

δ

Within ±25% of initial value for capacitors of 16V or less.

Within ±20% of initial value for capacitors of 25V or more.

200% or less of initial specified value

Initial specified value or less

Capacitance change

Leakage current

tan

δ

Within ±10% of initial value

Initial specified value or less

Initial specified value or less

Dimension table in next page.

WZ

Voltage

V

6.3

10

16

25

35

50

Code

j

A

C

E

V

H

Chip Type, Wide Temperature Range

High Temperature (260°C) Reflow

WT

High

Temperature

Reflow

CAT.8100V