FN6607 Rev.5.02

Page 5

Feb 13, 2025

ISL7119RH, ISL7119EH Datasheet

2.4

Electrical Specifications

VS = ±15V, GND = 0V, TA = 25°C, unless otherwise noted

Parameter

Symbol

Test Condition[1]

1. RH and EH Device meet all levels M, D, P, L, R, and F of irradiation. However, these devices are only tested at the F level in accordance with

MIL-STD-883 method 1019 condition A. Pre and post irradiation values are identical unless otherwise specified in table. When performing post

irradiation electrical measurements for any RHA level, TA = +25°C (see Ordering Information). Device type 01 may be dose rate sensitive in a

space environment and may demonstrate enhanced low dose rate effects. In addition, an EH device is production lot acceptance tested on a

wafer-by-wafer basis to 300krad(Si) in accordance with MIL-STD-883 method 1019 condition A, and 50krad(Si) in accordance with MIL-STD-883

method 1019 condition D.

Min

Max

Unit

Input Offset Voltage

VOS

+VS = 15V, -VS = -15V,

RS ≤ 5kΩ, RL = 1.4kΩ pull up to 5V

VCM = 12V

-8

+8

mV

VCM = -12V

+VS = 5V, -VS = 0V,

RS ≤ 5kΩ, RL = 1.4kΩ pull up to 5V

VCM = 1V

VCM = 3V

Saturation Voltage

VSAT

+VS = 15V, -VS = -15V, VIN ≤ -8mV, ISINK ≤ 25mA

-

1.8

V

+VS = 3.5V, -VS = -1V, VIN ≤ -8mV, ISINK ≤ 3.2mA

-

0.65

V

Common-Mode Rejection Ratio

CMRR

+VS = 15V, -VS = -15V,

RS ≤ 5kΩ, RL = 1.4kΩ pull up to 5V

VCM = 12V

74

-

dB

VCM = -12V

Input Offset Current

IIO

+VS = 15V, -VS = -15V,

VCM = 12V

-

150

nA

VCM = -12V

+VS = 5V, -VS = 0V,

VCM = 1V

VCM = 3V

Input Bias Current

IB

+VS = 15V, -VS = -15V, RL = 1.4kΩ

-

1000

nA

+VS = 5V, -VS = 0V, RL = 1.4kΩ

Positive Supply Current

ICC

+VS = 15V, -VS = -15V, ISINK ≤ 25mA

-

12

mA

Negative Supply Current

IEE

+VS = 15V, -VS = -15V, ISINK ≤ 25mA

-5

-

mA

Voltage Gain

AVOL

+VS = 15V, -VS = -15V, RL = 10kΩ pull up to 15V,

∆VOUT = 10V

74

-

dB

+VS = 5V, -VS = 0V, RL = 10kΩ pull up to 5V,

∆VOUT = 10V

72

-

dB

Output Leakage Current

ICEX

+VS = 15V, -VS = -1V, VIN < VIO(min), VOUT = 35V

-

20

μA

Input Voltage Range

VIN

+VS = 15V, -VS = -15V

-12

12

V

+VS = 5V, -VS = 0V

1

3

V

Response Time

tPD

+VS = 15V, -VS = -15V, RL = 500Ω pull up to 5V,

CL = 50pF to GND, VIN = VIO + 5mV, ∆VIN = 100mV

-

160

ns

+VS = 5V, -VS = 0V, RL = 500Ω pull up to 5V,

CL = 50pF to GND, VIN = VIO + 5mV, ∆VIN = 100mV

-

185

ns