AS5040 datasheet(13/28 Pages) AMSCO

13 / 28 page

AS5040 10-BIT PROGRAMMABLE MAGNETIC ROTARY ENCODER

Revision 1.6, 03-Oct-06

www.austriamicrosystems.com

Page 13 of 28

In te rn a l

te s t b it

digita l

V unprogram m ed

V program m ed

CS n

CL K

1 6

P rog

Pro g EN

Md 1

Md 0

A nalog R ead ba c k D a ta a t P rog

Ou tp E N

tLoadProg

CL K Aread

P ro g ch an ges to O u tp ut

V ref

P ow e r-o n-

Re s e t;

tu rn o ff

s u pply

Div 1

Div 0

ccw

Figure 16: OTP register analog read

10 Alignment Mode

The alignment mode simplifies centering the magnet over

the chip to gain maximum accuracy and XY-alignment

tolerance.

This electrical centering method allows a wider XY-

alignment tolerance (0.485mm radius) than mechanical

centering (0.25mm radius) as it eliminates the placement

tolerance of the die within the IC package (+/- 0.235mm).

Alignment mode can be enabled with the falling edge of

CSn while Prog = logic high (Figure 17). The Data bits

D9-D0 of the SSI change to a 10-bit displacement

amplitude output. A high value indicates large X or Y

displacement, but also higher absolute magnetic field

strength. The magnet is properly aligned, when the

difference between highest and lowest value over one full

turn is at a minimum.

Under normal conditions, a properly aligned magnet will

result in a reading of less than 32 over a full turn.

The MagINCn and MagDECn indicators will be = 1 when

the alignment mode reading is < 32. At the same time,

both hardware pins MagINCn (#1) and MagDECn (#2) will

be pulled to VSS. A properly aligned magnet will

therefore produce a MagINCn = MagDECn = 1 signal

throughout a full 360° turn of the magnet.

Stronger magnets or short gaps between magnet and IC

may show values larger than 32. These magnets are still

properly aligned as long as the difference between

highest and lowest value over one full turn is at a

minimum.

The alignment mode can be reset to normal operation

mode by a power-on-reset (disconnect / re-connect

power supply).

AlignMode enable

Prog

CSn

Read-out

via SSI

2µs

min.

2µs

min.

Figure 17: Enabling the alignment mode

11 3.3V / 5V Operation

The AS5040 operates either at 3.3V ±10% or at 5V

±10%. This is made possible by an internal 3.3V Low-

Dropout (LDO) voltage regulator. The internal supply

voltage is always taken from the output of the LDO,

meaning that the internal blocks are always operating at

3.3V.

For 3.3V operation, the LDO must be bypassed by

connecting VDD3V3 with VDD5V (see Figure 18).

For 5V operation, the 5V supply is connected to pin

VDD5V, while VDD3V3 (LDO output) must be buffered by

a 1...10µF capacitor, which is supposed to be placed

close to the supply pin (see Figure 18).

The VDD3V3 output is intended for internal use only It

must not be loaded with an external load.

The output voltage of the digital interface I/O’s

corresponds to the voltage at pin VDD5V, as the I/O

buffers are supplied from this pin (see Figure 18).

AS5040 数据表(PDF) 13 Page - ams AG

AS5040 数据表(HTML) 13 Page - ams AG

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

数据表下载