For technical support and further information visit http://power.ti.com

Environmental & Absolute Maximum Ratings (Voltages are with respect to GND)

Characteristics

Symbols

Conditions

Min

Typ

Max

Units

Track Input Voltage

Vtrack

–0.3

—

Vin + 0.3

V

Operating Temperature Range

Ta

Over Vin Range

–40 (i)

—

85

°C

Solder Reflow Temperature

Treflow

Surface temperature of module body or pins

235 (ii)

°C

Storage Temperature

Ts

—

–40

—

125

°C

Mechanical Shock

Per Mil-STD-883D, Method 2002.3

—

200

—

G’s

1 msec, ½ Sine, mounted

Mechanical Vibration

Mil-STD-883D, Method 2007.2

Suffix H

—

20

—

G’s

20-2000 Hz

Suffix S

—

20

—

Weight

—

—

3.7

—

grams

Flammability

—

Meets UL 94V-O

Notes:

(i) For operation below 0 °C the external capacitors must bave stable characteristics. use either a low ESR tantalum, Os-Con, or ceramic capacitor.

(ii) During reflow of SMD package version do not elevate peak temperature of the module, pins or internal components above the stated maximum.

10-A, 5-V Input Non-Isolated

Wide-Output Adjust Power Module

PTH05060W —5-V Input

SLTS216B – MAY 2003 – REVISED DECEMBER 2003

Specifications (Unless otherwise stated, T

a =25 °C, Vin =5 V, Vo =3.3 V, Cin =330 µF, Cout =0 µF, and Io =Iomax)

PTH05060W

Characteristics

Symbols

Conditions

Min

Typ

Max

Units

Output Current

Io

0.8 V

≤ V

o ≤ 3.6 V,

60 °C, 200 LFM airflow

0

—

10 (1)

A

25 °C, natural convection

0

—

10 (1)

Input Voltage Range

Vin

Over Io range

4.5

—

5.5

V

Set-Point Voltage Tolerance

Vo tol

—

—

±2 (2)

%Vo

Temperature Variation

∆Reg

temp

–40 °C <Ta < +85 °C

—

±0.5

—

%Vo

Line Regulation

∆Reg

line

Over Vin range

—

±10

—

mV

Load Regulation

∆Reg

load

Over Io range

—

±12

—

mV

Total Output Variation

∆Reg

tot

Includes set-point, line, load,

——±3 (2)

%Vo

–40 °C

≤ T

a ≤ +85 °C

Efficiency

η

Io =7 A

RSET = 698 Ω

Vo = 3.3 V

—

94

—

RSET = 2.21 kΩ Vo = 2.5 V

—

92

—

RSET = 4.12 kΩ Vo = 2.0 V

—

91

—

%

RSET = 5.49 kΩ Vo = 1.8 V

—

90

—

RSET = 8.87 kΩ Vo = 1.5 V

—

89

—

RSET = 17.4 kΩ Vo = 1.2 V

—

86—

RSET = 36.5 kΩ Vo = 1.0 V

—

85

—

Vo Ripple (pk-pk)

Vr

20 MHz bandwidth

—

25

—

mVpp

Over-Current Threshold

Io trip

Reset, followed by auto-recovery

—

20

—

A

Transient Response

1 A/µs load step, 50 to 100 % Iomax,

Cout =330 µF

ttr

Recovery Time

—

70

—

µSec

∆V

tr

Vo over/undershoot

—

100

—

mV

Margin Up/Down Adjust

∆V

o margin

—

± 5

—

%

Margin Input Current (pins 9 /10)

IIL margin

Pin to GND

—

– 8 (3)

—µA

Track Input Current (pin 8)

IIL track

Pin to GND

—

—

–130 (4)

µA

Track Slew Rate Capability

dVtrack/dt

Cout ≤ Cout(max)

—

—

1

V/ms

Under-Voltage Lockout

UVLO

Vin increasing

—

4.3

4.45

V

Vin decreasing

3.4

3.7

—

Inhibit Control (pin3)

Referenced to GND

Input High Voltage

VIH

Vin –0.5

—

Open (4)

V

Input Low Voltage

VIL

–0.2

—

0.6

Input Low Current

IIL inhibit

Pin to GND

—

–130

—

µA

Input Standby Current

Iin inh

Inhibit (pin 3) to GND, Track (pin 8) open

—

10

—

mA

Switching Frequency

ƒs

Over Vin and Io ranges

275

300

325

kHz

External Input Capacitance

Cin

330 (5)

——µF

External Output Capacitance

Cout

Capacitance value

non-ceramic

0

330 (6)

5,500 (7)

µF

ceramic

0

—

300

Equiv. series resistance (non-ceramic)

4

(8)

——

µF

Reliability

MTBF

Per Bellcore TR-332

5.7

—

—

106 Hrs

50 % stress, Ta =40 °C, ground benign

Notes: (1) See SOA curves or consult factory for appropriate derating.

(2) The set-point voltage tolerance is affected by the tolerance and stability of RSET. The stated limit is unconditionally met if RSET has a tolerance of 1 %

with 100 ppm/°C or better temperature stability.

(3) A small low-leakage (<100 nA) MOSFET is recommended to control this pin. The open-circuit voltage is less than 1 Vdc.

(4) This control pin has an internal pull-up to the input voltage Vin. If it is left open-circuit the module will operate when input power is applied. A small

low-leakage (<100 nA) MOSFET is recommended for control. For further information, consult the related application note.

(5) A 330 µF input capacitor is required for proper operation. The capacitor must be rated for a minimum of 500 mA rms of ripple current.

(6) An external output capacitor is not required for basic operation. Adding 330 µF of distributed capacitance at the load will improve the transient response.

(7) This is the calculated maximum. The minimum ESR limitation will often result in a lower value. Consult the application notes for further guidance.

(8) This is the typcial ESR for all the electrolytic (non-ceramic) output capacitance. Use 7 m

Ω as the minimum when using max-ESR values to calculate.