CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

PCZChipType,HigherCapacitance

High Temperature Range

Specifications

Temperature Characteristics

(Max.Impedance Ratio)

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Tangent of loss angle (tan δ)

ESR ( 1)

Leakage Current ( 2)

Performance Characteristics

Item

–55 to +150°C

16 to 63V

12 to 1000µF

± 20% at 120Hz, 20°C

Less than or equal to the specified value at 120Hz, 20°C

Less than or equal to the specified value at 100kHz, 20°C

After 2 minutes' application of rated voltage, leakage current is not more than 0.03CV.

Z(

–55°C) / Z(+20°C)

1.25

(100kHz)

Endurance

ESR after Endurance ( 1)

Damp Heat

(Steady State)

Resistance to

Soldering Heat

Marking

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 2000 hours at 150°C.

Less than or equal to the specified value at 100kHz, -40°C

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 2000 hours at 85°C , 85% RH.

After soldering the capacitor under the soldering conditions

prescribed here, the capacitor shall meet the specifications listed at

right.

Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.

The duration for over +230°C temperature at capacitor surface shall

not exceed 60 seconds.

In case peak temperature is 260°C or less, reflow soldering shall be

two times maximum.

Measurement for solder temperature profile shall be made at the

capacitor top.

Navy blue print on the case top

Capacitance change

tan δ

Leakage current ( 2)

ESR ( 1)

Within ± 20% of initial capacitance value ( 3)

150% or less of the initial specified value

200% or less of the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current ( 2)

ESR ( 1)

Within ± 20% of initial capacitance value ( 3)

150% or less of the initial specified value

200% or less of the initial specified value

Less than or equal to the initial specified value

Capacitance change

tan δ

Leakage current ( 2)

ESR ( 1)

Within ± 10% of the initial capacitance value ( 3)

130% or less than the initial specified value

130% or less than the initial specified value

Less than or equal to the initial specified value

High reliability.

Low ESR, High ripple current.

Long life of 2000 hours at 150°C.

SMD type : Lead free reflow soldering condition at

260°C peak complete correspondence.

Compliant to the RoHS directive (2011/65/EU,(EU)2015/863).

ESR after Endurance at -40°C.

AEC-Q200 Qualified. Please contact us for details.

1 ESR should be measured at both of the terminal ends closest where the terminals

protrude through the plastic platform.

2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of

applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

Positive

H

0.3 max.

C±0.2

Series

Voltage (V:35V)

Plastic platform

Lot No.

Capacitance

Negative

L

±0.5

Standard

Negative

Positive

Vibration Resistance

H

0.3 max.

C±0.2

L±0.5

Plastic platform

Aid electrode

Series

Voltage (V:35V)

Lot No.

Capacitance

Dimensions

PCZ

High Temperature

PCH

Dimension table in next page.

P

1

C

2

Z

3

1

4

V

5

2

6

2

7

1

8

M

9

C

10

L

11

1

12

G

13

S

14

Configuration

Taping code

Size code

Capacitance tolerance (±20%)

Rated capacitance (220µF)

Rated voltage (35V)

Series name

Type

Standard

Vibration

Resistance

Code

Size

L

※Please ask for

Part Number.

Type numbering system (Example : 35V 220µF)

φ8×10L(φ8×10.5L),φ10×10L(φ10×10.5L),φ10×12.7L(φ10×13.2L) :

The vibration structure-resistant product is also available upon request, please ask for details.

( ) : Size of the vibration structure-resistant product.

(mm)

Vibration Resistance

φ8×10.5L

1.1to1.5

Size

φD

L

A

B

C

E

H

φ10×13.2L

10.0

12.7

11.0

10.3

10.3

4.6

1.1to1.5

φ10×10.5L

10.0

10.0

11.0

10.3

10.3

4.6

1.1to1.5

8.0

10.0

9.0

8.3

8.3

3.1

Size

φD

L

A

B

C

E

H

(mm)

Standard

φ8

×7L

8.0

6.9

9.0

8.3

8.3

3.2

0.8 to 1.1

φ8

× 10L

8.0

9.9

9.0

8.3

8.3

3.2

0.8 to 1.1

φ8

×12L

8.0

11.9

9.0

8.3

8.3

3.2

0.8 to 1.1

φ10

× 10L

10.0

9.9

11.0

10.3

10.3

4.6

0.8 to 1.1

φ10

×8L

10.0

7.9

11.0

10.3

10.3

4.6

0.8 to 1.1

φ10

×12.7L

10.0

12.6

11.0

10.3

10.3

4.6

0.8 to 1.1

Voltage

V 16 20 25 35 50 63

Code C

D E

V H

J

Frequency coefficient of rated ripple current

Frequency

Coefficient

※ I : Leakage Current (µA), C : Rated Capacitance (µF), V : Rated Voltage (V)

120Hz 1kHz 10kHz 100kHz or more

0.05 0.30 0.70

1.00

CAT.8100N