3

Electronic Solutions Division

Interconnect Solutions

http://www.3Mconnectors.com

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ Four-Wall Header

.100” × .100” Latch/Ejector, Straight and Right Angle

D3000 Series

TS-2245-F

Sheet 3 of 4

Table 1

Pin Qty

3M Part

Number

Dimensions

Polarizing

Notches

A

B

C

D

06

3869

1.065 (27.05)

0.905 (22.99)

0.665 (16.89)

0.505 (12.83)

B*

08

3889

1.165 (29.59)

1.005 (25.53)

0.765 (19.43)

0.605 (15.37)

B*

10

3793

1.265 (32.13)

1.105 (28.04)

0.865 (21.97)

0.705 (17.91)

BC

14

3314

1.465 (37.21)

1.305 (33.12)

1.065 (27.05)

0.905 (22.99)

BC

16

3408

1.565 (39.75)

1.405 (35.66)

1.165 (29.59)

1.005 (25.53)

ABC

20

3428

1.765 (44.83)

1.605 (40.74)

1.365 (34.67)

1.205 (30.61)

ABC

24

3627

1.965 (49.91)

1.805 (45.82)

1.565 (39.75)

1.405 (35.69)

ABC

26

3429

2.065 (52.45)

1.905 (48.36)

1.665 (42.29)

1.505 (38.23)

ABC

30

3440

2.265 (57.53)

2.105 (53.44)

1.865 (47.37)

1.705 (43.31)

ABC

34

3431

2.465 (62.61)

2.305 (58.52)

2.065 (52.45)

1.905 (48.39)

ABC

40

3432

2.765 (70.23)

2.605 (66.14)

2.365 (60.07)

2.205 (56.01)

ABC

50

3433

3.265 (82.93)

3.105 (78.84)

2.865 (72.77)

2.705 (68.71)

ABC

60

3372

3.765 (95.63)

3.605 (91.54)

3.365 (85.47)

3.205 (81.41)

ABC

64

3764

3.965 (100.71)

3.805 (96.62)

3.565 (90.55)

3.405 (86.49)

ABC

* Available without center notch B. Contact 3M.

Inch

(mm)

± .005

± .1

± .01

Tolerance Unless Noted

.0

.00

.000

[ ] Dimensions for

Reference only

Table 2

3M Part

Number Suffix

Contact Tail

Dim E

Pin Cross Section

Dimension G

Dim F

Diagonals

Corner Radii

-5XX2

Solder Tail for

.062 [1.57]

Thick PC Board

.112 ± .010

[2.84]

.0245 ± .0005

[0.622]

.028 ± ..001

[0.71]

.0075 Ref

[0.191]

Ø.035 ±.003

[0.89] (See Note 3)

-6XX2

Notes:

1. Notches A & C will accomodate 3M Polarizing Keys (3M Part #3518 or #N3518).

2. Mounting hardware: From solder side of pc board use #4-24 thread cutting screw (3M Part # 3341-5) and .116 [2.95] dia mounting hole.

For right angle version only, #2-56 bolt and nut (3M Part # 3341-6) with .106 [2.69] dia mounting hole may be used. See illustrations on page 4.

3. Contact your 3M sales representative for custom requirements.

CL

"Y"

.41

[10.4]

Max to Edge of PCB

for Daisy Chain

ø.106

[2.69]

or ø.116

[2.95]

(See Note 2)

.029

[0.74]

.100 ± .003

[2.54]

Position 1

.232

[5.89]

C

Recommended Mounting Hole Pattern

(Right Angle)

.100 ± .003

[2.54]

Dim G

ø.106

[2.69]

or ø.116

[2.95]

(See Note 2)

Position 1

.100 ± .003

[2.54]

.100 ± .003

[2.54]

.060

[1.52]

.300

[7.62]

Side to Side Stackability

B

Recommended Mounting Hole Pattern

(Straight)

.352

[8.94]

CL

“Y”

Dim G

Ordering Information

D3XXX - XX02AR

Pin Configuration

5 = Right Angle Solder Tails

6 = Straight Solder Tails

3M Part Number

(See Table 1)

Latch/Ejector System

0 = No Latch/Ejector installed

2 = Short Roll Pin Latch/Ejectors

3 = Long Roll Pin Latch/Ejectors

Tail

02 = for .062 [1.57] thick board