ALUMINUM ELECTROLYTIC CAPACITORS

CAT.8100M

U

U

V

Code

6.3

j

10

A

16

C

25

E

35

V

50

H

Voltage

Type numbering system (Example : 16V 100

µF)

U

1

C

2

L

3

1

4

C

5

1

6

0

7

1

8

M

9

C

10

L

11

1

12

G

13

S

14

Configuration

Size code

Taping code

Capacitance tolerance (±20%)

Rated capacitance (100µF)

Rated voltage (16V)

Series name

Type

10 × 10

A

B

C

E

L

H

4 × 5.8

1.8

4.3

4.3

1.0

5.8

0.5 to 0.8

5 × 5.8

2.1

5.3

5.3

1.3

5.8

0.5 to 0.8

6.3 × 5.8

2.4

6.6

6.6

2.2

5.8

0.5 to 0.8

6.3 × 7.7

2.4

6.6

6.6

2.2

7.7

0.5 to 0.8

10 × 7.7

3.2

10.3

10.3

4.5

7.7

0.8 to 1.1

8 × 10

2.9

8.3

8.3

3.1

10

0.8 to 1.1

8 × 6.2

3.3

8.3

8.3

2.3

6.2

0.5 to 0.8

3.2

10.3

10.3

4.5

10

0.8 to 1.1

(mm)

10 × 13.5

3.2

10.3

10.3

4.5

13.5

0.8 to 1.1

φ D × L

(φ4 to φ8 × 6.2)

(φ8 × 10, φ10)

Chip Type

0.3 max.

C±0.2

H

H

0.3 max.

C±0.2

L±0.3

L±0.5

Series name

Capacitance

Lot No.

Lot No.

Capacitance

Plastic platform

Plastic platform

Series name

Trade mark

Voltage (C : 16V )

Voltage (E : 25V )

Negative

Positive

Negative

Positive

Specifications

Item

Performance Characteristics

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Leakage Current

Stability at Low Temperature

Endurance

Shelf Life

Resistance to soldering

heat

Marking

– 55 to +105°C

6.3 to 50V

10 to 2200

µF

± 20% at 120Hz, 20°C

After 2 minutes' application of rated voltages at 20°C, leakage current is not more than 0.01 CV or 3 (

µA), whichever is greater.

After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at

20°C, they shall meet the specified values for the endurance characteristics listed above.

The capacitors are kept on a hot plate for 30 seconds, which is

maintained at 250°C. The capacitors shall meet the characteristic

requirements listed at right when they are removed from the plate

and restored to 20°C .

Black print on the case top.

6.3

2

3

4

Z(—25°C) / Z(+20°C)

Z(—40°C) / Z(+20°C)

Z(—55°C) / Z(+20°C)

Measurement frequency : 120Hz

Measurement frequency : 120Hz at 20°C

Capacitance Change

tan δ

Leakage current

Within ± 10% of the initial capacitance value

Less than or equal to the initial specified value

Less than or equal to the initial specified value

Capacitance Change

tan δ

Leakage current

Within ± 30% of the initial capacitance value

200% or less than the initial specified value

Less than or equal to the initial specified value

Rated voltage (V)

tan δ (max.)

Rated voltage (V)

Impedance ratio

ZT / Z20 (max.)

10

2

3

4

16

2

3

4

25

2

3

3

35

2

3

3

50

2

3

3

6.3

0.26

10

0.19

16

0.16

25

0.14

35

0.12

50

0.10

Tangent of loss angle (tan δ)

The specifications listed at right shall be met when the

capacitors are restored to 20°C after the rated voltage is

applied for 2000 hours at 105°C.

φ D

4 to 6.3

8 (6.2L)

CL

CL

10(7.7L)

CL

8(10L) •

10(10L,13.5L)

NL

Code

Trade mark

1

1: Size φ8 × 6.2 only

Pressure

relief vent

2

2 : Except : φ10 × 7.7L

U

Dimension table in next page.

UCM

Smaller

Higher capacitance

Frequency

Coefficient

50Hz

0.35

120Hz

0.50

300Hz

0.64

1kHz

0.83

10kHz or more

1.00

Frequency coefficient of rated ripple current

※ I : Leakage Current (µA), C : Rated Capacitance (µF), V : Rated Voltage (V)