ALUMINUM ELECTROLYTIC CAPACITORS

Dimension table in next page.

※ I : Leakage Current (μA), C : Rated Capacitance (μF), V : Rated Voltage (V)

50Hz

0.35

120Hz

0.50

300Hz

0.64

1kHz

0.83

10kHz or more

1.00

Frequency

Coefficient

Frequency coefficient of rated ripple current

U

Item

Performance Characteristics

Category Temperature Range

Rated Voltage Range

Rated Capacitance Range

Capacitance Tolerance

Leakage Current

Endurance

Shelf Life

Resistance to soldering

heat

Marking

Stability at Low Temperature

– 55 to +105°C

6.3 to 100V

1 to 3300

µF

±20% at 120Hz, 20°C

After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01 CV or 3 (

µA), whichever is greater.

After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at

20°C, they shall meet the specified values for the endurance characteristics listed above.

The capacitors are kept on a hot plate for 30 seconds, which is

maintained at 250°C. The capacitors shall meet the characteristic

requirements listed at right when they are removed from the

plate and restored to 20°C.

6.3

2

3

4

Z(—25°C) / Z(+20°C)

Z(—40°C) / Z(+20°C)

Z(—55°C) / Z(+20°C)

Measurement

frequency :120Hz

Measurement

frequency:120Hz at 20°C

For capacitance of more than 1000

µF, add 0.02 for every increase of 1000µF. (φ12.5 to φ18)

Black print on the case top.

Capacitance Change

tan δ

Leakage current

Within ± 10% of the initial capacitance value

Less than or equal to the initial specified value

Less than or equal to the initial specified value

Rated voltage (V)

tan δ (max.)

Rated voltage (V)

Impedance ratio

(max.)

10

2

3

4

16

2

3

4

25

2

3

3

35

2

3

3

50

2

3

3

63

2

3

3

80

2

3

3

100

2

3

3

6.3

0.26

10

0.19

16

0.16

25

0.14

35

0.12

50

0.10

63

0.08

80

0.08

100

0.07

Tangent of loss angle (tan δ)

The specifications listed below shall be met when

the capacitors are restored to 20°C after the rated

voltage is applied at 105°C for the conditions

listed at right.

U

U

U

6.3

∼ 50V

63

∼100V

∼7.7L

2000hrs.

2000hrs.

13.5L

∼

5000hrs.

5000hrs.

φ10×13.5L

5000hrs.

—

10L

5000hrs.

2000hrs.

Rated Voltage

Size ( mm )

Capacitance Change

tan δ

Leakage current

Within ± 30% of the initial capacitance value

200% or less than the initial specified value

300% or less than the initial specified value for 63V or more

Less than or equal to the initial specified value

Specifications

Configuration

Standard

Code

CS(φ6.3(7.7L))

NS(φ8(10L)

・φ10(10L)・

φ12.5 or more)

CL(φ6.3 or less

・

φ8(6.2L)

・φ10(7.7L))

NL(φ8(10L)

・

φ10(10L,13.5L)

・

NJ

(φ12.5 or more)

Configuration

Vibration

Resistance

H

0.3 max.

C±0.2

L±0.5

Lot No.

Capacitance

Plastic platform

Series

Trade mark

Voltage ( E : 25V )

Negative

Positive

Pressure

relief vent

2

2 : Except : φ10 × 7.7L

0.3 max.

C±0.2

H

L±0.3

Series

Capacitance

Lot No.

Plastic platform

Voltage ( j : 6.3V )

Negative

Positive

Trade mark

1

1: Size φ8 × 6.2 only

Trade mark

Voltage

Series

Capacitance

Lot No.

L±1.0

C±0.2

H

Plastic platform

Pressure

relief vent

0.3 max.

Positive

Negative

V

Code

6.3

j

10

A

16

C

25

E

35

V

50

H

63

J

80

K

100

2A

U

1

C

2

D

3

1

4

C

5

1

6

0

7

1

8

M

9

C

10

L

11

1

12

G

13

S

14

Configuration

Size code

Taping

code

Capacitance tolerance (±20%)

Rated capacitance (100

µF)

Rated voltage (16V)

Series name

Type

φ4 to 10

φ12.5 to 18

GS

MS

Code

Size

Type numbering system (Example : 16V 100

µF)

(φ4 to φ8 × 6.2)

(φ8 × 10, φ10)

(φ12.5 to φ18)

Voltage

A

B

C

E

L

H

4 × 5.8

1.8

4.3

4.3

1.0

5.8

0.5 to 0.8

5 × 5.8

2.1

5.3

5.3

1.3

5.8

0.5 to 0.8

6.3 × 5.8

2.4

6.6

6.6

2.2

5.8

0.5 to 0.8

6.3 × 7.7

2.4

6.6

6.6

2.2

7.7

0.5 to 0.8

8 × 6.2

3.3

8.3

8.3

2.3

6.2

0.5 to 0.8

8 × 10

2.9

8.3

8.3

3.1

10

0.8 to 1.1

10 × 7.7

3.2

10.3

10.3

4.5

7.7

0.8 to 1.1

10 × 10

3.2

10.3

10.3

4.5

10

0.8 to 1.1

10 × 13.5

3.2

10.3

10.3

4.5

13.5

0.8 to 1.1

φD×L

12.5×13.5

5.15

13.6

13.6

(3.3)

13.5

1.0 to 1.4

16 × 16.5

5.65

17.1

17.1

(5.8)

16.5

1.0 to 1.4

18 × 16.5

6.65

19.1

19.1

(5.8)

16.5

1.0 to 1.4

8×10 10×10

6.3×7.7

φ

12.5

φ

16

φ

18

A

B

C

E

2.9

8.3

8.3

3.1

3.2

10.3

10.3

4.5

L

10

10

H

1.1 to 1.5

2.4

6.6

6.6

2.2

7.7

0.5 to 0.8

1.1 to 1.5

4.8

13.6

13.6

(4.0)

13.5

1.0 to 1.4

5.4

17.1

17.1

(6.3)

6.4

19.1

19.1

(6.3)

16.5

1.0 to 1.4

16.5

1.0 to 1.4

φD×L

(φ6.3 )【Vibration Resistance】

(φ 8 , φ10)

【Vibration Resistance】

(φ12.5 to φ18) 【Vibration Resistance】

(mm)

Standard

Vibration Resistance

(mm)

Positive

Negative

Capacitance

Series

Voltage (V:35V)

H

0.3 max.

C±0.2

L

±1.0

Positive

Negative

H

C±0.2

Plastic platform

Pressure relief vent

0.3 max

L±1.0

Aid electrode

Trade mark

Voltage

Series

Capacitance

Lot No.

Pressure relief vent

Lot No.

Lot No.

Capacitance

Series

Trade mark

Voltage (V : 35V )

H

Plastic platform

Negative

0.3 max.

C±0.2

L±1.0

Positive

Plastic platform

※ φ6.3 × 5.8L or less, φ8×6.2L, φ10×7.7L, φ10×13.5L :

　The vibration structure-resistant product can't support.

CAT.8100N