STM32F412RGY7P datasheet(119/201 Pages) STMICROELECTRONICS

119 / 201 page

DocID028087 Rev 7

119/201

STM32F412xE/G

Electrical characteristics

166

6.3.13

EMC characteristics

Susceptibility tests are performed on a sample basis during device characterization.

Functional EMS (electromagnetic susceptibility)

While a simple application is executed on the device (toggling 2 LEDs through I/O ports).

the device is stressed by two electromagnetic events until a failure occurs. The failure is

indicated by the LEDs:

•

Electrostatic discharge (ESD) (positive and negative) is applied to all device pins until

a functional disturbance occurs. This test is compliant with the IEC 61000-4-2 standard.

•

FTB: A burst of fast transient voltage (positive and negative) is applied to VDD and VSS

through a 100 pF capacitor, until a functional disturbance occurs. This test is compliant

with the IEC 61000-4-4 standard.

A device reset allows normal operations to be resumed.

The test results are given in Table 53. They are based on the EMS levels and classes

defined in application note AN1709.

When the application is exposed to a noisy environment, it is recommended to avoid pin

exposition to disturbances. The pins showing a middle range robustness are: PA0, PA1,

PA2, on LQFP144 packages and PDR_ON on WLCSP49.

As a consequence, it is recommended to add a serial resistor (1 k

Ω maximum) located as

close as possible to the MCU to the pins exposed to noise (connected to tracks longer than

50 mm on PCB).

Designing hardened software to avoid noise problems

EMC characterization and optimization are performed at component level with a typical

application environment and simplified MCU software. It should be noted that good EMC

performance is highly dependent on the user application and the software in particular.

Therefore it is recommended that the user applies EMC software optimization and

prequalification tests in relation with the EMC level requested for his application.

Software recommendations

The software flowchart must include the management of runaway conditions such as:

•

Corrupted program counter

•

Unexpected reset

•

Critical Data corruption (control registers...)

Table 52. EMS characteristics for LQFP144 package

Symbol

Parameter

Conditions

Level/

Class

VFESD

Voltage limits to be applied on any I/O pin

to induce a functional disturbance

VDD = 3.3 V, LQFP144

TA = +25 °C, fHCLK = 100 MHz,

conforms to IEC 61000-4-2

VEFTB

Fast transient voltage burst limits to be

applied through 100 pF on VDD and VSS

pins to induce a functional disturbance

VDD = 3.3 V, LQFP144

TA = +25 °C, fHCLK = 100 MHz,

conforms to IEC 61000-4-4

STM32F412RGY7P 数据表(PDF) 119 Page - STMicroelectronics

STM32F412RGY7P 数据表(HTML) 119 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

数据表下载